HP Workstation xw6000 Adaptec SCSI RAID 2120S: Installation Guide - Page 45

Novell NetWare, Installing the Driver for a Boot Controller in a New NetWare5.1 or 6 Server

Get HP Workstation xw6000 PDF manuals and user guides View all HP Workstation xw6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Adaptec SCSI RAID 2120S/2200S Installation Guide Novell NetWare The Adaptec SCSI RAID Installation CD contains device drivers for NetWare 5.1 and 6.x. The following Novell support packs are the minimum level required before installing Adaptec SCSI RAID controller software and drivers: NetWare Revision Level 5.1 6.0 Support Pack 5 2 After you have installed the drivers, you can use the normal NetWare procedures for modifying disk partitions, applying hot fixes, or performing volume maintenance. Adaptec Storage Manager-Browser Edition will not run on a NetWare system. Creating and managing arrays on a NetWare system may be done using any of the following: ■ Using ARC during the starting of the system. ■ Using the managed system components installed on the NetWare system, and a remote Windows or Linux system running Adaptec Storage Manager-Browser Edition. ■ Using Command Line Interface on the NetWare system in DOS mode. Installing the Driver for a Boot Controller in a New NetWare 5.1 or 6 Server In this scenario, you are installing the Adaptec SCSI RAID controller as a boot controller in a new NetWare 5.x or 6.x server. To install the driver: 1 Install the Adaptec SCSI RAID controller as the primary controller and attach the disk drives. 2 Start the server. During restart, press Ctrl+A to start ARC. Use ARC to create the RAID. For details, refer to Using the Adaptec RAID Configuration (ARC) Utility on page 2-9. 3 Install and configure a secondary controller, if any. 3-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
3-14
Adaptec SCSI RAID 2120S/2200S Installation Guide
Novell NetWare
The
Adaptec SCSI RAID Installation CD
contains device drivers for
NetWare 5.1
and 6.x. The following Novell support packs are the
minimum level required before installing Adaptec SCSI RAID
controller software and drivers:
After you have installed the drivers, you can use the normal
NetWare procedures for modifying disk partitions, applying hot
fixes, or performing volume maintenance.
Adaptec Storage Manager-Browser Edition will not run on a
NetWare system. Creating and managing arrays on a NetWare
system may be done using any of the following:
■
Using ARC during the starting of the system.
■
Using the managed system components installed on the
NetWare system, and a remote Windows or Linux system
running Adaptec Storage Manager-Browser Edition.
■
Using Command Line Interface on the NetWare system in DOS
mode.
Installing the Driver for a Boot Controller in a New NetWare 5.1
or 6 Server
In this scenario, you are installing the Adaptec SCSI RAID
controller as a boot controller in a new NetWare 5.x or 6.x server.
To install the driver:
1
Install the Adaptec SCSI RAID controller as the primary
controller and attach the disk drives.
2
Start the server. During restart, press
Ctrl+A
to start ARC. Use
ARC to create the RAID. For details, refer to
Using the Adaptec
RAID Configuration (ARC) Utility
on page 2-9
.
3
Install and configure a secondary controller, if any.
NetWare Revision Level
Support Pack
5.1
5
6.0
2