HP Workstation xw6000 Adaptec SCSI RAID 2120S: Installation Guide - Page 50

UnixWare 7 and OpenUNIX 8, Installing the Driver on a New System

Get HP Workstation xw6000 PDF manuals and user guides View all HP Workstation xw6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Installing the Driver 5 To run the installpkg utility, type installpkg -d disk/. SCO UNIX reads the disk and prompts you to enter the package name to be installed. 6 Type aacraid_tar.z and press Return. 7 After the package is installed, rebuild the kernel. 8 Restart the system. 9 Install the new kernel. 10 Add devices to the controller. UnixWare 7 and OpenUNIX 8 Both UnixWare 7 and OpenUNIX 8 use the same procedures for adding the driver to the system, whether an initial installation or just adding to an existing system. The driver disk you create will be specific to one operating system or the other. Once the driver disk is created, there is no difference in the installation. Installing the Driver on a New System In this scenario, you are installing the controller and driver for a system on which either OpenUNIX 8 or UNIXWare 7 is being installed as the operating system. The operating system will be installed on an Adaptec RAID controller-based RAID. To install the driver: 1 Install and configure your Adaptec controller and hard disk drives according to the instructions in Chapter 2. 2 Create the driver disk as shown at the beginning of this chapter. 3 Early in the operating system installation, you will be shown a window labeled Choose One, insert the driver disk, select the Install HBA diskette entry, then press F10. The driver will load from the driver disk and return to the HBA screen. Select Proceed with Installation and press F10. 4 Complete the installation as appropriate. 5 When the installation completes, remove the driver disk and reboot the system. The boot driver installation process is complete. 3-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
3-19
Installing the Driver
5
To run the
installpkg
utility, type
installpkg -d disk/
.
SCO UNIX reads the disk and prompts you to enter the package
name to be installed.
6
Type
aacraid_tar.z
and press
Return
.
7
After the package is installed, rebuild the kernel.
8
Restart the system.
9
Install the new kernel.
10
Add devices to the controller.
UnixWare 7 and OpenUNIX 8
Both UnixWare 7 and OpenUNIX 8 use the same procedures for
adding the driver to the system, whether an initial installation or
just adding to an existing system. The driver disk you create will be
specific to one operating system or the other. Once the driver disk
is created, there is no difference in the installation.
Installing the Driver on a New System
In this scenario, you are installing the controller and driver for a
system on which either OpenUNIX 8 or UNIXWare 7 is being
installed as the operating system. The operating system will be
installed on an Adaptec RAID controller-based RAID.
To install the driver:
1
Install and configure your Adaptec controller and hard disk
drives according to the instructions in Chapter 2.
2
Create the driver disk as shown at the beginning of this chapter.
3
Early in the operating system installation, you will be shown a
window labeled
Choose One
, insert the driver disk, select the
Install HBA diskette
entry, then press
F10
. The driver will load
from the driver disk and return to the HBA screen. Select
Proceed with Installation
and press
F10
.
4
Complete the installation as appropriate.
5
When the installation completes, remove the driver disk and
reboot the system.
The boot driver installation process is complete.