HP dc73 HP Blade Workstation Client series - Embedded OS Version 10.xx - Page 42

Example installation from the USB key, Install Cleanly

Get HP dc73 - Blade Workstation Client PDF manuals and user guides View all HP dc73 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

7-2 Example installation from the USB key In this section, an example installation is performed that includes a clean installation (not an upgrade) plus setting of network parameters for the client computer. Embedded OS 10.50 is used further as an example. The installation steps are as follows: 1. Plug the USB key containing the Embedded OS 10.xx image into a USB port on the client computer. While either the front or back USB ports will work, use of a back USB port is recommended to minimize the possibility of damaging the extending USB key. 2. Cycle power on the client computer, which will initiate a boot from the USB key. The first screen will prompt you to select a keyboard language (see Figure 7-7). Use the up and down arrow keys to select a keyboard language, and press Enter. Figure 7-7 Keyboard language selection 3. Next you'll be prompted to select either Upgrade, Install, or Run (see Figure 7-8). Upgrade allows the OS to be installed while preserving client settings saved in the /settings directory. Install does a complete installation of the operating system, overwriting previous settings. Run allows the operating system to run directly from the USB key, and is primarily for troubleshooting. For this example, select Install Cleanly, and press Enter. Figure 7-8 Select Install Cleanly 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
42
7-2 Example installation from the USB key
In this section, an example installation is performed that includes a clean installation (not an upgrade) plus setting
of network parameters for the client computer. Embedded OS 10.50 is used further as an example. The
installation steps are as follows:
1.
Plug the USB key containing the Embedded OS 10.xx image into a USB port on the client computer. While
either the front or back USB ports will work, use of a back USB port is recommended to minimize the
possibility of damaging the extending USB key.
2.
Cycle power on the client computer, which will initiate a boot from the USB key. The first screen will prompt
you to select a keyboard language (see Figure 7-7). Use the up and down arrow keys to select a keyboard
language, and press
Enter
.
Figure 7-7
Keyboard language selection
3.
Next you’ll be prompted to select either
Upgrade
,
Install
, or
Run
(see Figure 7-8). Upgrade allows the OS
to be installed while preserving client settings saved in the
/settings
directory. Install does a complete
installation of the operating system, overwriting previous settings. Run allows the operating system to run
directly from the USB key, and is primarily for troubleshooting. For this example, select
Install Cleanly
, and
press
Enter
.
Figure 7-8
Select
Install Cleanly