HP dx2100 HP Compaq dx2100 MT Business PC Service Reference Guide (1st Edition - Page 40

Service Considerations - ram

Get HP dx2100 - Microtower PC PDF manuals and user guides View all HP dx2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Identifying the Chassis, Routine Care, and Disassembly Preparation 5.4 Service Considerations Listed below are some of the considerations that you should keep in mind during the disassembly and assembly of the computer. 5.4.1 Power Supply Fan The power supply fan is a variable-speed fan based on the temperature in the power supply. Ä CAUTION: The cooling fan is on when the computer is "ON" or in "Suspend to RAM" modes. The cooling fan is off when the computer is in "Dormant", Suspend to Disk", or "Soft Off" modes.. The cooling fan is always on when the computer is either in the "On," "Standby," or "Suspend" modes. You must disconnect the power cord from the power source before opening the computer to prevent system board or component damage. 5.4.2 Tools and Software Requirements To service the computer, you need the following: ■ Torx T-15 screwdriver (Compaq screwdriver with bits, PN 161946-001) ■ Torx T-15 screwdriver with small diameter shank (for certain front bezel removal) ■ Flat-bladed screwdriver (may sometimes be used in place of the Torx screwdriver) ■ Diagnostics software ■ Compaq tamper-resistant T-15 wrench (Smart Cover FailSafe Key, PN 166527-001) or Compaq tamper-resistant bits (Smart Cover FailSafe Key, PN 166527-002) 5.4.3 Screws The screws used in the computer are not interchangeable. They may have standard or metric threads and may be of different lengths. If an incorrect screw is used during the reassembly process, it can damage the unit. HP strongly recommends that all screws removed during disassembly be kept with the part that was removed, then returned to their proper locations. ✎ Metric screws have a black finish. U.S. (Unified Standard) screws have a silver finish and are only used on hard drives. ✎ As each subassembly is removed from the computer, it should be placed away from the work area to prevent damage. 5-6 404569-001 Service Reference Guide, dx2100 MT

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
5–6
404569-001
Service Reference Guide, dx2100 MT
Identifying the Chassis, Routine Care, and Disassembly Preparation
5.4 Service Considerations
Listed below are some of the considerations that you should keep in mind during the disassembly
and assembly of the computer.
5.4.1 Power Supply Fan
The power supply fan is a variable-speed fan based on the temperature in the power supply.
Ä
CAUTION:
The cooling fan is on when the computer is “ON” or in “Suspend to RAM” modes.
The cooling fan is off when the computer is in “Dormant”, Suspend to Disk”, or “Soft Off” modes..
The cooling fan is always on when the computer is either in the “On,” “Standby,” or “Suspend” modes.
You must disconnect the power cord from the power source before opening the computer to prevent
system board or component damage.
5.4.2 Tools and Software Requirements
To service the computer, you need the following:
■
Torx T-15 screwdriver (Compaq screwdriver with bits, PN 161946-001)
■
Torx T-15 screwdriver with small diameter shank (for certain front bezel removal)
■
Flat-bladed screwdriver (may sometimes be used in place of the Torx screwdriver)
■
Diagnostics software
■
Compaq tamper-resistant T-15 wrench (Smart Cover FailSafe Key, PN 166527-001) or
Compaq tamper-resistant bits (Smart Cover FailSafe Key, PN 166527-002)
5.4.3 Screws
The screws used in the computer are not interchangeable. They may have standard or metric
threads and may be of different lengths. If an incorrect screw is used during the reassembly
process, it can damage the unit. HP strongly recommends that all screws removed during
disassembly be kept with the part that was removed, then returned to their proper locations.
Metric screws have a black finish.
U.S. (Unified Standard) screws have a silver finish and are only used on hard drives.
As each subassembly is removed from the computer, it should be placed away from the work
area to prevent damage.