HP dx2200 HP Compaq dx2200 MT Business PC, 1st Edition - Page 26

Entering a User Password, Entering a Supervisor Password, Changing a User or Supervisor Password - shuts off

Get HP dx2200 - Microtower PC PDF manuals and user guides View all HP dx2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Desktop Management 2. As soon as the computer is turned on, press the F10 key to enter Computer Setup. ✎ If you do not press the F10 key at the appropriate time, you must turn the computer off, then on again, and press the F10 key again to access the utility. If you are using a PS/2 keyboard, you may see a Keyboard Error message-disregard it. 3. Select Set User Password and follow the instructions on the screen. 4. Before exiting, click Save and Exit Setup. Entering a User Password To enter a user password, complete the following steps: 1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart. 2. When the prompt appears on the monitor, type your current password, then press Enter. ✎ Type carefully; for security reasons, the characters you type do not appear on the screen. If you enter the password incorrectly, inclining beeping tones are heard. Try again. Entering a Supervisor Password If a supervisor password has been established on the computer, you will be prompted to enter it each time you run Computer Setup. 1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart. 2. As soon as the computer is turned on, press the F10 key to enter Computer Setup. ✎ If you do not press the F10 key at the appropriate time, you must turn the computer off, then on again, and press the F10 key again to access the utility. If you are using a PS/2 keyboard, you may see a Keyboard Error message-disregard it. 3. When the prompt appears on the monitor, type the supervisor password, then press the Enter key. ✎ Type carefully; for security reasons, the characters you type do not appear on the screen. If you enter the password incorrectly, inclining beeping tones are heard. Try again. Changing a User or Supervisor Password 1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart. 2. To change the user password, go to step 3. To change the supervisor password, as soon as the computer is turned on, press the F10 key to enter Computer Setup. 3-4 415606-001 Service Reference Guide, dx2200 MT

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
3–4
415606-001
Service Reference Guide, dx2200 MT
Desktop Management
2. As soon as the computer is turned on, press the
F10
key to enter Computer Setup.
✎
If you do not press the
F10
key at the appropriate time, you must turn the computer off, then on
again, and press the
F10
key again to access the utility.
If you are using a PS/2 keyboard, you may see a Keyboard Error message—disregard it.
3. Select
Set User Password
and follow the instructions on the screen.
4. Before exiting, click
Save and
Exit Setup.
Entering a User Password
To enter a user password, complete the following steps:
1.
Turn on or restart the computer. If you are in Windows, click
Start > Shut Down > Restart.
2. When the prompt appears on the monitor, type your current password, then press
Enter.
✎
Type carefully; for security reasons, the characters you type do not appear on the screen.
If you enter the password incorrectly, inclining beeping tones are heard. Try again.
Entering a Supervisor Password
If a supervisor password has been established on the computer, you will be prompted to enter it
each time you run Computer Setup.
1. Turn on or restart the computer. If you are in Windows, click
Start > Shut Down > Restart.
2. As soon as the computer is turned on, press the
F10
key to enter Computer Setup.
✎
If you do not press the
F10
key at the appropriate time, you must turn the computer off, then on
again, and press the
F10
key again to access the utility.
If you are using a PS/2 keyboard, you may see a Keyboard Error message—disregard it.
3.
When the prompt appears on the monitor, type the supervisor password, then press the
Enter
key.
✎
Type carefully; for security reasons, the characters you type do not appear on the screen.
If you enter the password incorrectly, inclining beeping tones are heard. Try again.
Changing a User or Supervisor Password
1. Turn on or restart the computer. If you are in Windows, click
Start > Shut Down > Restart.
2. To change the user password, go to step 3.
To change the supervisor password, as soon as the computer is turned on, press the
F10
key
to enter Computer Setup.