Hitachi 7K320 Specifications - Page 26

Radiation noise, Conductive noise

Page 26 highlights

6.1.3 Radiation noise 7K320 SATA OEM Specification The disk drive shall work without degradation of the soft error rate under the following magnetic flux density limits at the enclosure surface. Frequency (KHz) DC 0 < Frequency =< 60 60 < Frequency =

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176

7K320 SATA OEM Specification
Page 26 of 176
6.1.3
Radiation noise
The disk drive shall work without degradation of the soft error rate under the following magnetic flux
density limits at the enclosure surface.
Frequency (KHz)
Limits (uT RMS)
DC
1500 0-p
0 < Frequency =< 60
500 RMS
60 < Frequency =<100
250 RMS
100 < Frequency =< 200
100 RMS
200 < Frequency =< 400
50 RMS
Table 13. Magnetic flux density limits
6.1.4
Conductive noise
The disk drive shall work without soft error degradation in the frequency range from DC to 20 Mhz
injected through any two of the mounting screw holes of the drive when an AC current of up to 45 mA
(p-p) is applied through a 50-ohm resistor connected to any two mounting screw holes.