IBM 86481BU Installation Guide - Page 50

followings

Get IBM 86481BU PDF manuals and user guides View all IBM 86481BU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

for complete instructions for installing a SATA adapter in your server and for additional information about SATA adapters. Complete the following steps to cable an optional SATA adapter: 1. Install the SATA adapter (see "Installing an adapter" on page 31). 2. Disconnect the two SATA cables from the system board Serial ATA connectors and connect them to the SATA adapter. These are the signal cables for the SATA drives in bays 7 and 6. See "System-board internal connectors" on page 8 for the location of the Serial ATA connectors on the system board. Rear adapterretaining bracket Expansion-slot cover SATA adapter SATA signal cable connector SATA signal cable Front adapterretaining bracket 3. Complete the followings steps to connect the SATA signal cables that come with the adapter to the SATA back panel on the hard disk drive cage. Note: If you have placed the server on its side, adjust the instructions accordingly. a. Reach beneath the drive cage and push downward on the drive-cage-release latch; then, rotate the drive cage outward until the drive cage locks in the vertical position. 36 xSeries 226 Type 8648: Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
for
complete
instructions
for
installing
a
SATA
adapter
in
your
server
and
for
additional
information
about
SATA
adapters.
Complete
the
following
steps
to
cable
an
optional
SATA
adapter:
1.
Install
the
SATA
adapter
(see
“Installing
an
adapter”
on
page
31).
2.
Disconnect
the
two
SATA
cables
from
the
system
board
Serial
ATA
connectors
and
connect
them
to
the
SATA
adapter.
These
are
the
signal
cables
for
the
SATA
drives
in
bays
7
and
6.
See
“System-board
internal
connectors”
on
page
8
for
the
location
of
the
Serial
ATA
connectors
on
the
system
board.
SATA
adapter
SATA signal
cable connector
SATA signal
cable
Front adapter-
retaining bracket
Rear adapter-
retaining bracket
Expansion-slot
cover
3.
Complete
the
followings
steps
to
connect
the
SATA
signal
cables
that
come
with
the
adapter
to
the
SATA
back
panel
on
the
hard
disk
drive
cage.
Note:
If
you
have
placed
the
server
on
its
side,
adjust
the
instructions
accordingly.
a.
Reach
beneath
the
drive
cage
and
push
downward
on
the
drive-cage-release
latch;
then,
rotate
the
drive
cage
outward
until
the
drive
cage
locks
in
the
vertical
position.
36
xSeries
226
Type
8648:
Installation
Guide