IBM 86481BU Installation Guide - Page 53

Replacing, bezel, cover

Get IBM 86481BU PDF manuals and user guides View all IBM 86481BU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Replacing the bezel Complete the following steps to replace the bezel. Openings Tab Bezel Hooks Note: For hot-swap hard disk drive models, make sure the side cover is unlocked; then, slide the hot-swap lock bar on the bezel to the left (unlocked) before you begin. 1. Insert the two hooks on the bottom rear of the bezel onto the matching openings on the server chassis. 2. Insert the tab on the left side of the bezel into the matching hole on the chassis left front. 3. Push the top of the bezel toward the server until the two tabs at the top of the bezel snap into place. 4. For hot-swap hard-disk drive models, slide the lock bar to the right. The hot-swap lock bar locks when you lock the side cover key lock. 5. Lock the side cover. Replacing the side cover If you removed the support bracket or bezel, reinstall it before you replace the side cover. See "Removing and installing the support bracket" on page 14 and "Replacing the bezel." Note: The rear adapter retaining bracket rests against the server side cover. You might find it easier to lay the server on its side to replace the side cover. Complete the following steps to replace the side cover: 1. Check that all cables, adapters, and other components are installed and seated correctly and that you have not left loose tools or parts inside the server. 2. Make sure that the cover-release latch is in the unlocked (opened) position; then, insert the tabs inside the cover into the slots on the server chassis. Chapter 2. Installing options 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Replacing
the
bezel
Complete
the
following
steps
to
replace
the
bezel.
Openings
Hooks
Tab
Bezel
Note:
For
hot-swap
hard
disk
drive
models,
make
sure
the
side
cover
is
unlocked;
then,
slide
the
hot-swap
lock
bar
on
the
bezel
to
the
left
(unlocked)
before
you
begin.
1.
Insert
the
two
hooks
on
the
bottom
rear
of
the
bezel
onto
the
matching
openings
on
the
server
chassis.
2.
Insert
the
tab
on
the
left
side
of
the
bezel
into
the
matching
hole
on
the
chassis
left
front.
3.
Push
the
top
of
the
bezel
toward
the
server
until
the
two
tabs
at
the
top
of
the
bezel
snap
into
place.
4.
For
hot-swap
hard-disk
drive
models,
slide
the
lock
bar
to
the
right.
The
hot-swap
lock
bar
locks
when
you
lock
the
side
cover
key
lock.
5.
Lock
the
side
cover.
Replacing
the
side
cover
If
you
removed
the
support
bracket
or
bezel,
reinstall
it
before
you
replace
the
side
cover.
See
“Removing
and
installing
the
support
bracket”
on
page
14
and
“Replacing
the
bezel.”
Note:
The
rear
adapter
retaining
bracket
rests
against
the
server
side
cover.
You
might
find
it
easier
to
lay
the
server
on
its
side
to
replace
the
side
cover.
Complete
the
following
steps
to
replace
the
side
cover:
1.
Check
that
all
cables,
adapters,
and
other
components
are
installed
and
seated
correctly
and
that
you
have
not
left
loose
tools
or
parts
inside
the
server.
2.
Make
sure
that
the
cover-release
latch
is
in
the
unlocked
(opened)
position;
then,
insert
the
tabs
inside
the
cover
into
the
slots
on
the
server
chassis.
Chapter
2.
Installing
options
39