IBM 8852 User Guide - Page 35

Removing components before rack installation, Removing a power module

Get IBM 8852 - BladeCenter H Rack-mountable PDF manuals and user guides
UPC - 883436027069
View all IBM 8852 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

v While the device is still in its static-protective package, touch it to an unpainted metal part of the BladeCenter unit or rack for at least 2 seconds. This drains static electricity from the package and from your body. v Remove the device from its package and install it immediately without setting down. If it is necessary to set down the device, put it back into its static-protective package. v Take additional care when handling devices during cold weather. Heating reduces indoor humidity and increases static electricity. Removing components before rack installation Attention: See the BladeCenter H Problem Determination and Service Guide for removing components from the BladeCenter unit when the unit is connected to power. Use the following procedures to remove components from the BladeCenter unit before you install it in a rack and connect to power. Removing a power module To remove a power module, complete the following steps. Release buttons Release buttons 1. Read the safety information that begins on page v and "Installation guidelines" on page 18. 2. Press the blue release button on each end of the bezel. 3. Pull the bezel away from the BladeCenter unit. Chapter 3. Installing the BladeCenter unit and options 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
v
While the device is still in its static-protective package, touch it to an unpainted
metal part of the BladeCenter unit or rack for at least 2 seconds. This drains
static electricity from the package and from your body.
v
Remove the device from its package and install it immediately without setting
down. If it is necessary to set down the device, put it back into its
static-protective package.
v
Take additional care when handling devices during cold weather. Heating reduces
indoor humidity and increases static electricity.
Removing components before rack installation
Attention:
See the
BladeCenter H Problem Determination and Service Guide
for
removing components from the BladeCenter unit when the unit is connected to
power.
Use the following procedures to remove components from the BladeCenter unit
before you install it in a rack and connect to power.
Removing a power module
To remove a power module, complete the following steps.
Release buttons
Release buttons
1.
Read the safety information that begins on page v and “Installation guidelines”
on page 18.
2.
Press the blue release button on each end of the bezel.
3.
Pull the bezel away from the BladeCenter unit.
Chapter 3. Installing the BladeCenter unit and options
19