IBM 8852 User Guide - Page 41

and Health Administration or European Community Directives might govern,

Get IBM 8852 - BladeCenter H Rack-mountable PDF manuals and user guides
UPC - 883436027069
View all IBM 8852 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Note: Government regulations (such as those prescribed by Occupational Safety and Health Administration or European Community Directives) might govern noise level exposure in the workplace and might apply to you and your server installation. The actual sound pressure levels in your installation depend on a variety of factors, including the number of racks in the installation; the size, materials, and configuration of the room where you designate the racks to be installed; the noise levels from other equipment; the room ambient temperature; and employees' location in relation to the equipment. Compliance with such government regulations also depends on a variety of additional factors, including the duration of employees' exposure and whether employees wear hearing protection. It is recommended that you consult qualified experts in this field to determine whether you are in compliance with the applicable regulations. To install a blower module, complete the following steps. Handle (open) Release button 1. Read the safety information that begins on page v and "Installation guidelines" on page 18. 2. Make sure that the handle on the blower module is in the open position. 3. Orient the blower module to the selected blower-module bay: v For the upper bay, the handle must be on the right. v For the lower bay, the handle must be on the left. 4. Slide the module into the bay until it stops; then, push the handle to the closed position. Chapter 3. Installing the BladeCenter unit and options 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Note:
Government regulations (such as those prescribed by Occupational Safety
and Health Administration or European Community Directives) might govern
noise level exposure in the workplace and might apply to you and your
server installation. The actual sound pressure levels in your installation
depend on a variety of factors, including the number of racks in the
installation; the size, materials, and configuration of the room where you
designate the racks to be installed; the noise levels from other equipment;
the room ambient temperature; and employees' location in relation to the
equipment. Compliance with such government regulations also depends on a
variety of additional factors, including the duration of employees' exposure
and whether employees wear hearing protection. It is recommended that you
consult qualified experts in this field to determine whether you are in
compliance with the applicable regulations.
To install a blower module, complete the following steps.
Handle (open)
Release button
1.
Read the safety information that begins on page v and “Installation guidelines”
on page 18.
2.
Make sure that the handle on the blower module is in the open position.
3.
Orient the blower module to the selected blower-module bay:
v
For the upper bay, the handle must be on the right.
v
For the lower bay, the handle must be on the left.
4.
Slide the module into the bay until it stops; then, push the handle to the closed
position.
Chapter 3. Installing the BladeCenter unit and options
25