IBM 8852 User Guide - Page 43

Installing an I/O module, handle; the modules and fillers in I/O bays 7 through 10 each have two

Get IBM 8852 - BladeCenter H Rack-mountable PDF manuals and user guides
UPC - 883436027069
View all IBM 8852 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Installing an I/O module The BladeCenter unit has 10 hot-swap I/O-module bays that are compatible with three types of I/O modules (see "Major components of the BladeCenter H unit" on page 9 for the location of the I/O module bays). Note: Before you install a new I/O module, read the documentation that comes with the module for detailed instructions. To install an I/O module, complete the following steps. Single module filler Double module filler I/O module I/O module Release handle (open) Module filler Release handles (open) 1. Remove the module filler if one is installed. 2. Make sure that the release handles are in the open position. Note: The modules and fillers in I/O bays 1 through 6 each have one release handle; the modules and fillers in I/O bays 7 through 10 each have two release handles. 3. Slide the module into the module bay until it stops. 4. Push the release handle or handles to the closed position. 5. Connect all cables to the module. Chapter 3. Installing the BladeCenter unit and options 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Installing an I/O module
The BladeCenter unit has 10 hot-swap I/O-module bays that are compatible with
three types of I/O modules (see “Major components of the BladeCenter H unit” on
page 9 for the location of the I/O module bays).
Note:
Before you install a new I/O module, read the documentation that comes
with the module for detailed instructions.
To install an I/O module, complete the following steps.
I/O
module
Module
filler
I/O module
Single
module
filler
Double
module
filler
Release handles
(open)
Release handle
(open)
1.
Remove the module filler if one is installed.
2.
Make sure that the release handles are in the open position.
Note:
The modules and fillers in I/O bays 1 through 6 each have one release
handle; the modules and fillers in I/O bays 7 through 10 each have two
release handles.
3.
Slide the module into the module bay until it stops.
4.
Push the release handle or handles to the closed position.
5.
Connect all cables to the module.
Chapter 3. Installing the BladeCenter unit and options
27