IBM 8852 User Guide - Page 46

Installing an optical drive

Get IBM 8852 - BladeCenter H Rack-mountable PDF manuals and user guides
UPC - 883436027069
View all IBM 8852 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Installing an optical drive To install an optical drive, complete the following steps. Retainer clip Optical drive retainer tab Media tray release tabs Note: These instructions assume that the BladeCenter unit is connected to power. 1. Remove the media tray and optical drive filler (see "Removing an optical drive filler" on page 24). 2. Make sure that the media tray is on a clean, static-free surface with the circuit board facing up. Attention: To prevent damage to the circuit board, do not touch or apply pressure to the circuit board or any of its components. 3. Install the retainer clip on the side of the optical drive. 4. Carefully slide the optical drive into the bay on the media tray until it fully engages the connector and the retainer tab locks into place. 5. Carefully slide the media tray into the BladeCenter unit until the release tabs lock it into place. 6. Install the top and bottom bezels (see "Installing a bezel" on page 31). 30 BladeCenter H Type 8852, 7989, and 1886: Installation and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Installing an optical drive
To install an optical drive, complete the following steps.
Media tray
release tabs
Optical drive
retainer tab
Retainer clip
Note:
These instructions assume that the BladeCenter unit is connected to power.
1.
Remove the media tray and optical drive filler (see “Removing an optical drive
filler” on page 24).
2.
Make sure that the media tray is on a clean, static-free surface with the circuit
board facing up.
Attention:
To prevent damage to the circuit board, do not touch or apply
pressure to the circuit board or any of its components.
3.
Install the retainer clip on the side of the optical drive.
4.
Carefully slide the optical drive into the bay on the media tray until it fully
engages the connector and the retainer tab locks into place.
5.
Carefully slide the media tray into the BladeCenter unit until the release tabs
lock it into place.
6.
Install the top and bottom bezels (see “Installing a bezel” on page 31).
30
BladeCenter H Type 8852, 7989, and 1886: Installation and User’s Guide