IBM 8852 User Guide - Page 40

Removing an optical drive filler, Installing components, Installing a blower module

Get IBM 8852 - BladeCenter H Rack-mountable PDF manuals and user guides
UPC - 883436027069
View all IBM 8852 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Removing an optical drive filler To remove an optical drive filler, complete the following steps. Retainer clip Optical drive retainer tab Media tray release tabs Note: These instructions assume that the BladeCenter unit is connected to power. 1. Read the safety information that begins on page v and "Installation guidelines" on page 18. 2. Remove the top and bottom bezels (see "Removing a bezel" on page 23). 3. Press the release tabs on the top and bottom of the media tray; then, pull the tray out of the BladeCenter unit. 4. Place the media tray on a clean, static-free surface with the circuit board and optical drive filler facing up. Attention: To prevent damage to the circuit board, do not touch or apply pressure to the circuit board or any of its components. 5. Press the optical drive filler retainer tab and slide the optical drive filler out of the media tray. 6. Remove the retainer clip from the side of the optical drive filler. Installing components The following procedures are for reinstalling components or installing optional devices in the BladeCenter unit once the rack installation is complete. Installing a blower module Your BladeCenter might be equipped with standard blower modules (part number 44E5083), or it might be equipped with high-efficiency blower modules (part number 68Y8205). The standard and high-efficiency blower modules are not interchangeable and should not be mixed in the same BladeCenter unit. For a list of supported options for the BladeCenter, see the ServerProven® list at http://www.ibm.com/servers/eserver/serverproven/compat/us/. 24 BladeCenter H Type 8852, 7989, and 1886: Installation and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Removing an optical drive filler
To remove an optical drive filler, complete the following steps.
Media tray
release tabs
Optical drive
retainer tab
Retainer clip
Note:
These instructions assume that the BladeCenter unit is connected to power.
1.
Read the safety information that begins on page v and “Installation guidelines”
on page 18.
2.
Remove the top and bottom bezels (see “Removing a bezel” on page 23).
3.
Press the release tabs on the top and bottom of the media tray; then, pull the
tray out of the BladeCenter unit.
4.
Place the media tray on a clean, static-free surface with the circuit board and
optical drive filler facing up.
Attention:
To prevent damage to the circuit board, do not touch or apply
pressure to the circuit board or any of its components.
5.
Press the optical drive filler retainer tab and slide the optical drive filler out of
the media tray.
6.
Remove the retainer clip from the side of the optical drive filler.
Installing components
The following procedures are for reinstalling components or installing optional
devices in the BladeCenter unit once the rack installation is complete.
Installing a blower module
Your BladeCenter might be equipped with standard blower modules (part number
44E5083), or it might be equipped with high-efficiency blower modules (part number
68Y8205). The standard and high-efficiency blower modules are not
interchangeable and should not be mixed in the same BladeCenter unit.
For a list of supported options for the BladeCenter, see the ServerProven
®
list at
24
BladeCenter H Type 8852, 7989, and 1886: Installation and User’s Guide