Icom IC-M330 Instruction Manual english

Icom IC-M330 Manual

Get Icom IC-M330 PDF manuals and user guides View all Icom IC-M330 manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-M330 manual content summary:

  • Icom IC-M330 | Instruction Manual english - Page 1
    INSTRUCTION MANUAL VHF MARINE TRANSCEIVERS |M330 |M330E |M330G |M330GE
  • Icom IC-M330 | Instruction Manual english - Page 2
    years of trouble-free operation. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL - This instruction manual contains important operating instructions for the IC-M330, IC-M330E, IC-M330G, IC-M330GE. This instruction manual includes
  • Icom IC-M330 | Instruction Manual english - Page 3
    IN CASE OF EMERGENCY If your vessel requires assistance, contact other vessels and the Coast Guard by sending a distress call on Channel 16. USING CHANNEL 16 DISTRESS CALL PROCEDURE 1. "MAYDAY MAYDAY MAYDAY." 2. "THIS IS name of vessel). 3. Say your call sign or other indication of the vessel (AND
  • Icom IC-M330 | Instruction Manual english - Page 4
    OPERATION WARNING Icom requires the radio operator to meet the FCC Requirements for Radio Frequency Exposure. An omnidirectional antenna with gain not radius of the antenna, unless such persons (such as driver or radio operator) are shielded from antenna field by a grounded metallic barrier. The
  • Icom IC-M330 | Instruction Manual english - Page 5
    AVERTISSEMENT POUR LES OPÉRATEURS RADIO Icom exige que l'opérateur radio se conforme aux exigences de la FCC 65 DE LA FCC. CETTE DISTANCE ESTIMÉE TIENT COMPTE D'UN SYSTÈME INSTALLÉ SUR UN NAVIRE UTILISANT LA PUISSANCE MAXIMALE DE LA RADIO ET DES ANTENNES DONT LE GAIN MAXIMAL EST DE 9 dBi. Ne pas
  • Icom IC-M330 | Instruction Manual english - Page 6
    in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
  • Icom IC-M330 | Instruction Manual english - Page 7
    transceivers. To comply with FCC regulations, this sticker must be affixed in a location where it is readily seen from the operating controls of the radio, as show in the diagram below. Make sure the chosen location is clean and dry before applying the sticker. EXAMPLE: WARNING STICKER WARNING
  • Icom IC-M330 | Instruction Manual english - Page 8
    ! NEVER place the transceiver where normal operation of the vessel may be hindered, or where it could cause bodily injury. CAUTION: DO NOT install the transceiver and/or microphone less than 1 meter from the vessel's magnetic navigation compass. CAUTION: DO NOT use or leave the transceiver in
  • Icom IC-M330 | Instruction Manual english - Page 9
    endroit pouvant gêner le fonctionnement normal du navire, ou à un endroit où il pourrait causer des blessures corporelles. MISE EN GARDE : NE JAMAIS installer l'émetteur-récepteur et/ ou le microphone à moins d'1 mètre du compas de navigation magnétique du navire. MISE EN GARDE : NE JAMAIS utiliser
  • Icom IC-M330 | Instruction Manual english - Page 10
    that antenna of a maximum gain of 3 dB is used. If higher gain antenna are required then please contact your Icom distributor for revised installation recommendations. Operation: The exposure to RF electromagnetic field is only applicable when this device is transmitting. This exposure is naturally
  • Icom IC-M330 | Instruction Manual english - Page 11
    KEY ICON DESCRIPTION The keys are described in this manual as followings: zzThe keys that have an icon on them RADIO OPERATION WARNING iii AVERTISSEMENT POUR LES OPÉRATEURS RADIO iv FCC INFORMATION v INFORMATION FCC v NOTE vi PRECAUTIONS vii PRÉCAUTIONS viii RECOMMENDATION ix INSTALLATION
  • Icom IC-M330 | Instruction Manual english - Page 12
    55 ■■Fuse replacement 55 ■■Cleaning 55 ■■Supplied accessories 55 ■■Mounting the transceiver 56 ■■MBF-5 installation 57 10. SPECIFICATIONS AND OPTIONS 58 ■■Specifications 58 ■■Options 59 11. TROUBLESHOOTING 60 12. CHANNEL LIST 61 13. TEMPLATE 63 14. INFORMATION 65 ■■About CE and DOC
  • Icom IC-M330 | Instruction Manual english - Page 13
    a radio telephone is compulsory. However, even 11 if you are not required to have these on hand it is your 12 responsibility to be thoroughly acquainted with all pertinent rules and regulations. 13 14 NOTE: Even though the IC-M330/IC-M330E/IC-M330G/ IC-M330GE is capable of operation on VHF
  • Icom IC-M330 | Instruction Manual english - Page 14
    screen. 6 MENU KEY [MENU] Push to display or close the Menu screen. 7 POWER/VOLUME/SQUELCH SWITCH [PWR/VOL/ SQL] (Also described as [DIAL] in this manual.) zzHold down for 1 second to turn the transceiver ON or OFF. zzRotate or push once to display the volume level setting screen, then rotate to
  • Icom IC-M330 | Instruction Manual english - Page 15
    STATUS INDICATOR 2 ••STBY: Standby mode. 3 ••RT: Displayed while in the Radio Telephone (RT) mode. LLReturns to the Standby mode if no operation occurs 4 the "CH Auto SW" is set to "Ignore after 10 sec." or "Manual." 11 8 LOCAL INDICATOR 12 Displayed when the RF Attenuation is ON. (For
  • Icom IC-M330 | Instruction Manual english - Page 16
    keys" on the next page for details. 14 POSITION/TIME READOUTS Readouts the current position and time when valid GPS data is received, or when manually entered. Received GPS data: ••"NO POS NO TIME" is displayed if no GPS data has been received, and then a warning message is displayed for 2 minutes
  • Icom IC-M330 | Instruction Manual english - Page 17
    PANEL DESCRIPTION 2 DDSoftware key functions Distress Call DISTRESS (p. 22) Push to display the "Distress" screen to select the nature of distress, then to make a call. LL DTRS is displayed in the Multiple-task mode. (For only the USA version) NEVER MAKE A DISTRESS CALL IF YOUR SHIP OR A PERSON
  • Icom IC-M330 | Instruction Manual english - Page 18
    KEYS p. 9) Push to change the channel. LLWhen the "FAV on MIC" item is set to "ON," you can select Favorite channels, change scanning direction or manually resume a scan. (p. 51) e TRANSMIT POWER KEY [HI/LO] zzPush to set the power level to high or low. LLSome channels are set to only low
  • Icom IC-M330 | Instruction Manual english - Page 19
    ■■Entering the MMSI code The Maritime Mobile Service Identity (MMSI: DSC self ID) code consists of 9 digits. You can only enter the code when turning ON the transceiver for the first time. This
  • Icom IC-M330 | Instruction Manual english - Page 20
    is successfully entered, the screen displays "ATIS ID Successfully Registered," and then enters the operating screen. LLYou can check the ATIS ID in "Radio Info" on the Menu screen. TIP: ••Select a number using [◄] and Push [ENT] to enter the selected number. ••Select "←" or "→," or rotate [DIAL
  • Icom IC-M330 | Instruction Manual english - Page 21
    4 BASIC OPERATION ■■Selecting a channel DDRegular Channel You can select a channel by pushing [▲] or [▼]. DDChannel 16 Channel 16 is the distress and safety channel. It is used to establish the initial contact with a station, and for emergency communications. Channel 16 is monitored during both
  • Icom IC-M330 | Instruction Manual english - Page 22
    CAN DSC           ATIS   1. Push [MENU]. ••The Menu screen is displayed. 2. Push or rotate [DIAL] to select "Radio Settings," then push [ENT]. ••The "RADIO SETTINGS" screen is displayed. 3. Push or rotate [DIAL] to select "Channel Group," then push [ENT]. ••The "CHANNEL
  • Icom IC-M330 | Instruction Manual english - Page 23
    Alert LLSee page 51 for details on the Weather Alert function. 1. Push [MENU]. 2. Push or rotate [DIAL] to select "Radio Settings," and then push [ENT]. ••The "RADIO SETTINGS" screen is displayed. 3. Select "WX Alert," and then push [ENT]. ••The "WX Alert" screen is displayed. 4. Select "On
  • Icom IC-M330 | Instruction Manual english - Page 24
    . You can set your most often-used channel as your Call channel in each Channel Group for quick recall. 1. Display the "CALL CHANNEL" screen. [MENU] > Radio Settings > Call Channel 2. Push or rotate [DIAL] to adjust, then push [ENT] to set. LLPush EXIT to exit the Menu screen. 2. Push or rotate
  • Icom IC-M330 | Instruction Manual english - Page 25
    BASIC OPERATION 4 ■■Receiving and transmitting CAUTION: DO NOT transmit without an antenna. 1. Push [▲] or [▼] to select the channel to call on. ••The channel number and name are briefly displayed. (Only when "CH Close-up" is ON.) LLYou cannot transmit on Channel 70. L L is displayed while
  • Icom IC-M330 | Instruction Manual english - Page 26
    operating channel and weather channel, using numbers, uppercase letters, symbols, and a space. This enables easy recognition of the channels or stations. All VHF marine channels are set with default names. 1. Push [▲] or [▼] to select the channel to edit. 2. Push [◄] or [►] to display NAME . LLYou
  • Icom IC-M330 | Instruction Manual english - Page 27
    also monitoring Channel 16. 4 LOnly the Favorite channels are scanned. 5 ••Set the scan type to "Priority Scan" or "Normal Scan" on the "Radio Settings" screen. (p. 50) CH 01 CH 02 6 7 Normal Scan The Normal Scan sequentially searches through all Favorite channels. However, Channel 16 is
  • Icom IC-M330 | Instruction Manual english - Page 28
    is received. LLWhen a signal is received, the scan pauses until it disappears, or resumes after 5 seconds, depending on the Scan Timer setting in "Radio Settings." LLA beep sounds and "16" blinks when a signal is received on Channel 16 during a Priority scan. 4. To stop the scan, push SCAN
  • Icom IC-M330 | Instruction Manual english - Page 29
    DUALWATCH/TRI-WATCH (Except for Dutch version) 6 ■■Description ■■Operation 1 Dualwatch and Tri-watch are convenient to monitor Channel 1. Select Dualwatch or Tri-watch on the Menu screen. 2 16 while you are operating on another channel. 2. Push [▲] or [▼] to select a channel. 3 3. Push
  • Icom IC-M330 | Instruction Manual english - Page 30
    7 DSC OPERATION ■■DSC address ID DDEntering an Individual ID You can enter a total of 60 Individual IDs, and assign names to them of up to 10 characters. 1. Display the "INDIVIDUAL ID" screen. [MENU] > DSC Settings > Individual ID ••"No ID" is displayed if no ID is entered. 2. Push ADD . ••"The
  • Icom IC-M330 | Instruction Manual english - Page 31
    1. Display the "INDIVIDUAL ID" screen. 2 1. Display the "GROUP ID" screen. [MENU] > DSC Settings > Individual ID 3 2. Push [▲] or [▼] to select "ICOM 2." 4 [MENU] > DSC Settings > Group ID ••"No ID" is displayed if no ID is entered. 5 2. Push ADD . ••The Group ID's entry screen is displayed
  • Icom IC-M330 | Instruction Manual english - Page 32
    the vessel's position, date and time. If no GPS data is received, manually enter the position and Universal Time Coordinated (UTC) time. NOTE: ••The manual entry is disabled while valid GPS data is received. ••The manually entered position and time is valid only for 23.5 hours, or until turning
  • Icom IC-M330 | Instruction Manual english - Page 33
    to return to the operating screen. 9 TIP: A default Distress alert contains: 10 ••Nature of distress: Undesignated distress ••Position information: The latest GPS, or manually input 11 position, that is held for 23.5 hours, or until you turn OFF 12 the transceiver. 13 14 15 16 ••The
  • Icom IC-M330 | Instruction Manual english - Page 34
    7 DSC OPERATION DDRegular call Select the nature of the Distress call to include in the Regular Distress call. 1. Push DISTRESS . ••The "DISTRESS" screen is displayed. 2. Push [ENT] to enter the Nature selection mode. 3. Push or rotate [DIAL] to select the nature of the Distress, then push [ENT]. (
  • Icom IC-M330 | Instruction Manual english - Page 35
    DDDistress call software key description While waiting for an Acknowledgement: CANCEL :  Cancels the Distress call and enables you to send a Cancel call. (See the right column) RESEND :  Enables you to resend the Distress call by holding down [DISTRESS] again. PAUSE :  Pauses the countdown to
  • Icom IC-M330 | Instruction Manual english - Page 36
    the station to send an Individual call to, and the push [ENT]. ••Returns to the "OTHER DSC" screen. LLYou can also select "Manual Input" to manually enter the target station. 6. Select "Channel," and then push [ENT]. 24 7. Select a channel to assign, and then push [ENT]. LLThe assigned channels
  • Icom IC-M330 | Instruction Manual english - Page 37
    Acknowledgement "Unable to comply" Push ALARM OFF to turn OFF the alarm. ••The Acknowledge information is displayed. LLPush STBY , and then OK to return to the operating screen. DSC OPERATION 7 1 DDSending an Individual Acknowledgement When you have received an Individual call (p. 33), send an 2
  • Icom IC-M330 | Instruction Manual english - Page 38
    7 DSC OPERATION DDSending an Individual Acknowledgement (Continued) 3. Push ABLE , UNABLE , or NEW CH to select the Acknowledgement type. •• ABLE (Able to Comply): Sends an Acknowledgement call without any changes. •• UNABLE (Unable to Comply):Sends an Acknowledgement call but cannot communicate.
  • Icom IC-M330 | Instruction Manual english - Page 39
    DSC OPERATION 7 DDSending an All Ships call 1 All Ships, that have DSC transceiver, use Channel 70 as their listening channel. When you want to announce a 8. Push CALL to send the All Ships call. ••"Transmitting All Ships Call" is displayed, and then the 2 message to these ships, if they are
  • Icom IC-M330 | Instruction Manual english - Page 40
    ENT]. ••The "ADDRESS" screen is displayed. 5. Select the group to send a Group call to, and the push [ENT]. LLYou can also select "Manual Input" to manually enter the target group. 6. Select "Channel," and then push [ENT]. 7. Select the channel to assign, and then push [ENT]. LLThe assigned channels
  • Icom IC-M330 | Instruction Manual english - Page 41
    11 12 4. Select a station to send the Test call to. 8. Push STBY . ••"Terminate the procedure. Are you sure?" is displayed. 13 LLYou can also select "Manual Input" to manually enter the calling station. 9. Push OK to return to the operating screen. 14 15 16 29
  • Icom IC-M330 | Instruction Manual english - Page 42
    when you receive a Test call, the Auto ACK function automatically sends an Acknowledgement to the calling station (p. 42). If the function is set to "Manual," do the following steps to send an Acknowledgement. 1. After a Test call is being received, push ALARM OFF to turn OFF the alarm. 2. Push ACPT
  • Icom IC-M330 | Instruction Manual english - Page 43
    "Able to Comply" Acknowledgement, or push 9 UNABLE to send an "Unable to Comply" Acknowledgement. 10 LLIf no valid GPS position is received, 11 you can manually enter the position and time in "Position" item on this 12 screen. See "Entering the position and time" on page 20 for details. 13
  • Icom IC-M330 | Instruction Manual english - Page 44
    " blinks continuously until you display the call message. PAUSE (Pause): LL PAUSE is not displayed if the "CH Auto SW" item is set to "Manual." (p. 42) ••Pauses the countdown until the assigned channel is automatically selected. ••Select RESUME to resume the countdown. ••The call is saved in the DSC
  • Icom IC-M330 | Instruction Manual english - Page 45
    DSC OPERATION 7 ■■Receiving DSC calls (other) The transceiver receives the following types of DSC calls. ••Individual call (p. 33) ••Individual Acknowledgement call (p. 26) ••Group call (p. 34) ••All Ships call (p. 35) ••Position Request call (p. 36) ••Test call (p. 37) ••Test Acknowledgement call
  • Icom IC-M330 | Instruction Manual english - Page 46
    " blinks continuously until you display the call message. PAUSE (Pause): LL PAUSE is not displayed if the "CH Auto SW" item is set to "Manual." (p. 42) ••Pauses the countdown until the assigned channel is automatically selected. ••Select RESUME to resume the countdown. ••The call is saved in the DSC
  • Icom IC-M330 | Instruction Manual english - Page 47
    " blinks continuously until you display the call message. PAUSE (Pause) LL PAUSE is not displayed if the "CH Auto SW" item is set to "Manual." (p. 42) ••Pauses the countdown until the assigned channel is automatically selected. ••Select RESUME to resume the countdown. ••The call is saved in the DSC
  • Icom IC-M330 | Instruction Manual english - Page 48
    to "Auto," the Position Reply is automatically sent to the calling station. (p. 42) ••However, even if the Auto ACK function is set to "Manual," after receiving a Distress Acknowledgement, or while in the Distress Cancel call procedure, the Position Reply is automatically sent to the calling station
  • Icom IC-M330 | Instruction Manual english - Page 49
    ACK function automatically sends an Acknowledgement to the calling station (p. 42). ACPT (Accept) ••Accepts the call. 3 If the function is set to "Manual," the following screens are displayed. ••Displays the received call's information. ••The call is saved in the DSC Log. 4 5 When a Test call
  • Icom IC-M330 | Instruction Manual english - Page 50
    7 DSC OPERATION DDReceiving a Test Acknowledgement call After sending a Test call, the called station will send you a Test Acknowledgement call. When a Test Acknowledgement call is received: ••The alarm sounds for 2 minutes. ••"RCVD TEST ACK" is displayed. 1. Push ALARM OFF to turn OFF the alarm. 2.
  • Icom IC-M330 | Instruction Manual english - Page 51
    4. Push [▲] or [▼] to scroll through the log. 5. Push [ENT] to display the received call's information. EXIT : BACK : DEL : MMSI : Returns to the operating screen. Returns to the previous screen. Deletes the selected call log. LLThe confirmation screen is displayed before deleting. Saves the MMSI
  • Icom IC-M330 | Instruction Manual english - Page 52
    7 DSC OPERATION ■■Multiple-task mode (For only the USA version, depending on the presetting.) If the Multiple-task function is enabled, the transceiver can hold up to 7 tasks. Therefore, you can handle more than 2 DSC tasks simultaneously by switching between the DSC tasks. To use the Multiple-task
  • Icom IC-M330 | Instruction Manual english - Page 53
    DSC OPERATION 7 DDActivating the held DSC task 1. Push TASK to display the task list. ••The task list is displayed. 2. Push [▲] or [▼] to select the task that you want to activate. 3. Push ACTIVE to activate the task. ••The activated task information is displayed. 4. Push [PTT] to communicate. 5.
  • Icom IC-M330 | Instruction Manual english - Page 54
    : Differs depending on the version or presetting) Auto (Able): Automatically sends "Able to comply." Auto (Unable): Automatically sends "Unable to comply." Manual: Manually sends an Acknowledgement call. ••Position ACK (Default: Auto (Able)) Auto (Able): Automatically sends "Able to comply
  • Icom IC-M330 | Instruction Manual english - Page 55
    The received position data has not been updated for 10 minutes. 6 - The received position data has not been updated for 4 7 hours. - The manually entered position data has not been updated 8 for 23.5 hours. 9 ••Self-Terminate (Default: On) 10 An alarm sounds when duplicate DSC calls are
  • Icom IC-M330 | Instruction Manual english - Page 56
    7 DSC OPERATION ■■DSC Settings (Continued) Self-Test The Self-Test sends DSC signals to the receiving AF circuit to compare the sending and receiving signals at the AF level. Push [ENT] to start the Self-Test. LLWhen the sending and receiving DSC signals match, "OK" is displayed. Procedure (
  • Icom IC-M330 | Instruction Manual english - Page 57
    6 ••To ensure correct operation of the DSC function, make 7 sure you correctly set the CH70 SQL Level. (p.43) ••This instruction is for the MA-500TR. See the MA-510TR Instruction manual for the MA-510TR's step. 8 ••If Channel 70 is busy, the transceiver stands by until the channel becomes clear
  • Icom IC-M330 | Instruction Manual english - Page 58
    7 DSC OPERATION 1. After sending the Individual DSC call, the transponder will display "DSC Transmission COMPLETED." ••Push [CLEAR] to return to the screen displayed before you entered the Voice channel selection screen in step 2. ••The transceiver stands by on Channel 70 until an Acknowledgement
  • Icom IC-M330 | Instruction Manual english - Page 59
    8 MENU SCREEN ■■Using the Menu screen The Menu screen is used to set items, select options, and so on for the transceiver's functions. DDUsing the Menu screen Example: Setting the key beep to "Off." 1. Push [MENU]. ••The Menu screen is displayed. 2. Push or rotate [DIAL] to select "Configuration,"
  • Icom IC-M330 | Instruction Manual english - Page 60
    Log Reference Item Reference p. 38 Transmitted Call Log p. 39 48 Radio Settings Item Scan Type Scan Timer Dual/Tri-watch Channel Group Call DSC Settings Item Position Input Individual ID Group ID Auto ACK CH Auto SW Radio Info (p. 52) Reference Item p. 50 WX Alert p. 50 FAV Settings p.
  • Icom IC-M330 | Instruction Manual english - Page 61
    ) Setting for when a screen that is related to a Distress call 16 is displayed. ••RT (Default: 30 sec) Setting for when the transceiver is in the Radio Telephone mode. 49
  • Icom IC-M330 | Instruction Manual english - Page 62
    8 MENU SCREEN GPS Selects a satellite to be used for GPS (Global Positioning System) to pinpoint the geographic location of your transceiver anywhere in the world. This setting may not be usable, depending on the transceiver version or presetting. ••GPS (Always On) The GPS (Global Positioning
  • Icom IC-M330 | Instruction Manual english - Page 63
    MENU SCREEN 8 Channel Group Select the suitable channel group for your operating area. Select USA, INT, CAN, DSC, or ATIS depending on the transceiver version. LLSee page 10 for details. Call Chancel You can change your Call channel. The default setting differs, depending on the transceiver
  • Icom IC-M330 | Instruction Manual english - Page 64
    8 MENU SCREEN CH Display You can select the number of digits to display the channel number. 3 Digits: The channel number is displayed in 3 digits such as "01A." 4 Digits: The channel number is displayed in 4 digits such as "1001." LLThis setting may not be usable, depending on the transceiver
  • Icom IC-M330 | Instruction Manual english - Page 65
    9 CONNECTIONS AND MAINTENANCE ■■Connections q w e y r t 1 NMEA IN/OUT LEADS Green: Listener B (Data-L), GPS In (-) Yellow: Listener A (Data-H), GPS In (+) Connect to the NMEA output lines of a GPS receiver for position data. ••NMEA 0183 (ver. 2.0 or later) sentence format RMC, GGA, GNS, or
  • Icom IC-M330 | Instruction Manual english - Page 66
    4 ANTENNA CONNECTOR Connects to a marine VHF antenna with a PL-259 connector. CAUTION to the supplied GPS antenna. (For only the IC-M330G/IC-M330GE) NOTE: Be sure the GPS antenna is positioned target's MMSI code. See the transponder's instruction manual for connection details. Connect each lead to
  • Icom IC-M330 | Instruction Manual english - Page 67
    them. ■ Fuse replacement One fuse is installed in the supplied DC power cable. If the fuse blows or the transceiver stops functioning, track down the source of the problem, repair it, and replace the damaged fuse 15 GPS antenna and double-sided adhesive pad 16 (For only the IC-M330G/IC-M330GE) 55
  • Icom IC-M330 | Instruction Manual english - Page 68
    using the universal mounting bracket supplied with your transceiver. 1. Mount the bracket securely to a surface which is more than 10 mm thick and can support more than 5 kg using the 2 supplied screws (5 × 20 mm). NOTE: When mounting the transceiver on a board, fix the bracket to the board using
  • Icom IC-M330 | Instruction Manual english - Page 69
    9 CONNECTIONS AND MAINTENANCE ■■MBF-5 installation An optional MBF-5 flush mount kit is available for mounting the transceiver to a flat surface (less than 20 mm thick), such as an instrument panel.
  • Icom IC-M330 | Instruction Manual english - Page 70
    DSC (CH70) -5 dBµ emf (typical) (1% BER) Squelch sensitivity: IC-M330/IC-M330G Less than 0.32 μV IC-M330E/IC-M330GE Less than -2 dBμ emf • Intermodulation rejection ratio: FM IC-M330/IC-M330G More than 70 dB IC-M330E/IC-M330GE More than 68 dB DSC (CH70) More than 68 dB
  • Icom IC-M330 | Instruction Manual english - Page 71
    SPECIFICATIONS AND OPTIONS 10 ■■Options 1 DDGPS Antenna • Frequency : 1575.42 MHz ••MBF-5 flush mount kit To mount the transceiver to a panel. 2 3 • Channel: Acquisition, tracking: Maximum 24ch Calculation: Maximum 12ch ••MA-500TR/MA-510TR class b ais transponder 4 •
  • Icom IC-M330 | Instruction Manual english - Page 72
    11 TROUBLESHOOTING PROBLEM The transceiver does not turn ON. Little or no sound comes ID. First digit must be set to ʻ0ʼ for a Group ID. • 2 3.5 hours have passed since you manually entered the position. • The GPS position is invalid. • The GPS signal is not correctly received. • T he position
  • Icom IC-M330 | Instruction Manual english - Page 73
    12 CHANNEL LIST DDFor IC-M330/IC-M330G and USA channels for IC-M330E/IC-M330GE UK version Channel number Frequency (MHz) USA INT CAN Transmit Receive 01 01 156.050 160.650 1001 1001 156.050 156.050 02 02
  • Icom IC-M330 | Instruction Manual english - Page 74
    12 CHANNEL LIST DDFor IC-M330E/IC-M330GE zzInternational channels Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) CH Transmit Receive CH Transmit Receive CH Transmit Receive CH Transmit
  • Icom IC-M330 | Instruction Manual english - Page 75
    66.5 (2 5⁄8) 53 (2 3⁄32) R8 (5⁄16) Maximum 156.5 (6 5⁄32) 139 (5 15⁄32) 13 TEMPLATE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Unit: mm (inch) 63
  • Icom IC-M330 | Instruction Manual english - Page 76
  • Icom IC-M330 | Instruction Manual english - Page 77
    ■■About CE and DOC Hereby, Icom Inc. declares that the versions of IC-M330E/IC-M330GE which have the "CE" symbol on the product, comply with the essential requirements of the Radio Equipment Directive, 2014/53/EU, and the restriction of the use of certain hazardous substances in electrical and
  • Icom IC-M330 | Instruction Manual english - Page 78
    35 Sending 27 Antenna 55 AquaQuake 14 ATIS ID 8 Auto ACK (DSC Settings 42 B Backlight 12 Backlight, Configuration 49 C Call channel Radio Settings 51 Selecting 9 Setting 12 CH 70 SQL Level, DSC Settings..... 43 Channel Group 10 Name, editing 14 Selecting 9 Channel 16 9 Channel
  • Icom IC-M330 | Instruction Manual english - Page 79
    INDEX M MBF-5 installation 57 Menu screen Priority 15 Starting 16 Types 15 Scan Timer, Radio Settings 50 Scan Type, Radio Settings 50 Self test (DSC Settings 44 Simple 29 Time, entering 20 Transmitting 13 Tri-watch 17 Troubleshooting 60 U UTC Offset, Configuration 49 V Volume level
  • Icom IC-M330 | Instruction Manual english - Page 80
    How the World Communicates A7420D-1EX-7 Printed in Japan © 2017-2021 Icom Inc. Dec. 2021 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
VHF MARINE TRANSCEIVERS
|M330
|M330E
|M330G
|M330GE
INSTRUCTION MANUAL
INSTRUCTION MANUAL