Icom IC-V3500 Advanced Manual - Page 52

6. DTMF MEMORY Entering a DTMF code DTMF codes are used for auto-patching, controlling other equipment, and so on. The transceiver has up to 16 DTMF Memory channels (d0-dF) for up to 24 digit often-used DTMF codes. NOTE: To enter a DTMF code, "BAK" or "TVo" must be selected in the "OK" ([BANK/OPT] key) in the Initial Set mode. (p. 8-6) 1. Hold down [BANK OPT] for 1 second to enter the Option Set mode. 2. Push [SET LOCK] or [MONI ANM PA] to select "DTM" (DTMF Memory encoder). 3. Rotate [DIAL] to select "ON." ••The DTMF Memory encoder is turned ON. 4. Push [BANK OPT] to enter the DTMF Memory mode. ••The DTMF Memory Channel number blinks. LLThe previously entered DTMF code is displayed, if set. Example: Entering "5428AB453" into DTMF Memory channel "d3." Hold down [BANK OPT] for 1 second to enter the Option Set mode. AO NAR MID LOW SET ANM MONI Push [SET LOCK] or [MONI ANM PA] to select "DTM." MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN Rotate [DIAL] to select "ON." MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN NOTE: The previously entered code in the selected DTMF Memory channel will be cleared by doing the following steps. 5. Rotate [DIAL] to select the desired blank DTMF Memory channel. 6. Push [SET LOCK] or [MONI ANM PA] to enter the DTMF Memory Programming mode. ••The first digit (--) blinks. 7. Rotate [DIAL] to select the character. 8. Push [MONI ANM PA] to set the character. ••After the character is set, the next digit is automatically selected. LLPush [SET LOCK] to go back to the previous digit. LLWhen the 6th character is set, the next 6 blank digit group will be displayed. LLThe S/RF indicator shows the number of digits being displayed, as shown below. Indicator The number of digits being displayed 19 ~ 24 13 ~ 18 7 ~ 12 1 ~ 6 Push [BANK OPT] to enter the DTMF Memory mode. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN The DTMF Memory Channel number blinks. Rotate [DIAL] to select "d3." MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN Push [SET LOCK] to enter the DTMF Memory Programming mode. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN The first digit blinks. Rotate [DIAL] to select the character. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN Push [MONI ANM PA] to set the character. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN The next digit blinks. Repeat until the desired DTMF code entry is complete. 9. Repeat steps 7 and 8 until the desired DTMF code entry (up to 24 digits) is completed. 10. Push any key other than [SET LOCK] or [MONI ANM PA] to set the code and exit the DTMF Memory Programming mode. ••The 100 MHz digit is changed to "d." LLTo go back to the Option Set mode, hold down [BANK OPT] for 1 second. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN Push any key other than [SET LOCK] or [MONI ANM PA] to set the code and exit the DTMF Memory Programming mode. MUTE DIGITAL PRIO AO BUSY The 100 MHz digit is NAR MID LOW changed to "d." LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/MHz 6-2