Icom IC-V3500 Advanced Manual - Page 70

8. SET MODES Initial Set mode items Squelch type (Default: OF) Selects the squelch type. •• OF: Noise squelch. •• SS: S-meter squelch. The S-meter Squelch function disables the audio output from the speaker when the received signal is weaker than the specified S-meter squelch level. To turn ON the function, rotate [SQL] clockwise to a point past the 12 o'clock position. •• AT: Squelch attenuator. Approximately 20 dB of attenuation is obtained at the maximum setting. To turn ON the function, rotate [SQL] clockwise to a point past the 12 o'clock position. AO MUTE NAR MID LOW LOCK ANM SET MONI Display type (Default: FR) Selects the display type of the Memory mode. •• FR: The entered frequency is displayed. •• CH: The Memory Channel number is displayed. •• NM: The channel name is displayed. LLWhen "CH" is selected, the usable functions and Set mode items will be restricted as shown below. Usable functions when "CH" is selected: ••Memory scan ••Selecting an output power ••Adjusting the volume or squelch level ••Monitor function ••Lock function ••Set mode (Settable items are "SCP" (Scan Stop timer), "SCT" (Scan Resume timer), "DIM" (Display dimmer), "ATD" (Auto dimmer), "CON" (Display contrast), "BLK" (Bank Link function), and "MIC" (MIC gain).) AO MUTE NAR MID LOW LOCK ANM SET MONI Tone burst (Default: OF) Turns the Tone Burst function ON or OFF. •• OF: When you transmit a signal that superimposes a CTCSS tone, the other station may hear a short burst of noise from their receiver just after you stop transmitting. •• ON: When you transmit a signal that superimposes a CTCSS tone, the function mutes the noise from being heard in the other station's receiver. AO AO MUTE MUTE NAR NAR MID MID LOW LOW LOCK ANM LOCK ANM SET MONI SET MONI DTMF speed (Default: 1) Selects the DTMF transmit speed. •• 1: Transmits the DTMF codes at about 100 milliseconds per code (5 characters per second). •• 2: Transmits the DTMF codes at about 200 milliseconds per code (2.5 characters per second). •• 3: Transmits the DTMF codes at about 300 milliseconds per code (1.6 characters per second). •• 5: Transmits the DTMF codes at about 500 milliseconds per code (1 character per second). AO MUTE NAR MID LOW LOCK ANM SET MONI Voltage display (Default: ON) Selects whether or not to display the power source voltage. •• OF: The supplied voltage is not displayed. •• ON: When the transceiver is turned ON, the supplied voltage is displayed. AO AO MUTE MUTE NAR NAR MID MID LOW LOW LOCK ANM LOCK ANM SET MONI SET MONI [BANK/OPT] key (Default: BAK) Assigns the function to [BANK/OPT]. •• BAK: The Memory Bank mode and the Option Set mode are assigned. When the Memory mode is selected, push [BANK/OPT] to enter the Memory Bank mode. Hold down [BANK/OPT] for 1 second to enter the Option Set mode. •• EMR: T he Emergency Call function is assigned. Hold down [BANK/OPT] for 3 second to turn ON the function. •• TVo: The Temporary Volume function and the Option Set mode are assigned. Push [BANK/OPT] to change the volume level to the value set in the Temporary volume setting. Hold down [BANK/OPT] for 1 second to enter the Option Set mode. AO NAR MID LOW SET ANM MONI 8-6