Home » Icom Manuals » Two-Way Radios » Icom IC-V3500 » Manual Viewer

Icom IC-V3500 Advanced Manual - Page 83

Installing in a vehicle, Mounting the transceiver

Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

11. INSTALL AND CONNECTIONS Installing in a vehicle RRDANGER! NEVER place the transceiver where airbag deployment may be obstructed. RRWARNING! NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. DO NOT place the transceiver where hot or cold air blows directly onto it. 25º More than 100 mm (3.9 inches) height (recommended) DDMounting the transceiver You can install the transceiver on the dashboard or the console of your vehicle with the supplied mounting bracket. 1. Drill 4 holes where the supplied mounting bracket is to be installed. LLApproximately 5.5 ~ 5.6 mm (0.21 ~ 0.22 inch)(d) when using nuts, approximately 2 ~ 3 mm (0.08 ~ 0.12 inch)(d) when using self-tapping screws. 2. Insert the supplied screws, nuts, and washers through the mounting bracket and tighten. 3. Adjust the angle to suit your needs. NOTE: Contact your Icom dealer or car dealer for advice on installing in a vehicle. Mounting nut Screws When using selftapping screws Flat washer Spring washer Nut 11-3

Section	Page
ADVANCED OPERATIONS	4
Emergency Call function	5
Assigning the Emergency Call function to [BANK OPT]	5
Setting the Emergency frequency	5
Setting the Emergency alert volume	5
Using the Emergency Call function	6
Receiving an Emergency signal	7
Temporary Volume function	8
Assigning the Temporary Volume function to [BANK OPT]	8
Setting the Temporary Volume	8
Using the Temporary Volume function	8
REPEATER OPERATION	9
FM Repeater operation	10
Accessing a repeater	10
1750 Hz tone (Using the HM-133V)	11
Frequency Offset	12
Repeater Lockout	12
Reversed Duplex function	13
Auto Repeater function	13
Setting the Auto Repeater function ON/OFF	13
Frequency range and offset direction	13
Subaudible tones	14
Tone information	14
MEMORY OPERATION	15
General description	16
Memory channel contents	16
Selecting a Memory channel	17
Using the tuning dial	17
Using [▲] or [▼] on the HM-133V	17
Using the keypad on the HM-133V	17
Selecting a Call channel	18
Entering a Memory/Call channel	18
Copying the Memory channel contents	20
Memory/Call channel to VFO	20
Memory/Call channel to Call/Memory channel	21
Entering a channel name	22
Deleting a Memory channel	24
Setting a Memory Bank	25
Selecting a Memory Bank	27
Transferring a Memory channel to another bank	28
Deleting a Memory Bank	30
SCAN OPERATION	32
About scans	33
VFO scan	33
Memory scan	33
Memory Bank scan	33
[DIAL] operation during a scan	34
Squelch setting for a scan	34
Tuning step for a VFO scan	34
Skip function	34
When a signal is received	34
VFO scan	35
Memory scan	36
Memory Bank scan	37
Bank scan	37
Bank Link scan	39
Entering Scan Edges	41
Setting a Skip channel	42
PRIORITY WATCH	43
About the Priority watch	44
VFO frequency and a Memory/Call channel	45
VFO frequency and a Memory scan	46
VFO frequency and a Memory Bank scan	47
Bank scan	47
Bank Link scan	49
DTMF MEMORY	51
Entering a DTMF code	52
Transmitting a DTMF code	54
Automatic DTMF Memory transmission	54
Manual DTMF Memory transmission (Using the HM-133V microphone)	55
Manual DTMF code transmission (Using the HM-133V microphone)	55
Selecting the DTMF transmit speed	56
TONE SQUELCH AND POCKET BEEP	57
Tone/DTCS squelch	58
Tone squelch and DTCS squelch	58
Reverse Tone/DTCS squelch	58
Setting CTCSS tone or DTCS code	58
Setting DTCS polarity	58
Operation	59
Pocket Beep function	61
Waiting for a call from a specific station	61
Calling a waiting station using the Pocket Beep function	62
Tone scan	63
DTCS encoder (Transmit only)	64
SET MODES	65
Using the Set mode	66
Set mode items	66
Using the Initial Set mode	69
Initial Set mode items	69
Using the Option Set mode	72
Option Set mode items	72
OTHER FUNCTIONS	73
Weather channel operation (For only the USA version)	74
Selecting a Weather channel	74
Using the Weather Alert function	74
Microphone keys	75
[F-1] and [F-2] on the HM-133V microphone	75
The [UP] and [DN] keys on a microphone other than the HM-133V	75
One-touch PTT function	76
About the volume level and the squelch level	76
Resetting	77
Partial Reset	77
All Reset	77
PROGRAMMING	78
Programming operation	79
Cloning between two transceivers	79
Programming using a PC	80
INSTALL AND CONNECTIONS	81
Connecting a microphone	82
Connecting a DC power cable	82
Installing in a vehicle	83
Mounting the transceiver	83
Installing an antenna	84
Antenna location	84
Connecting to a battery	84
Fuse replacement	85
TROUBLESHOOTING	86