Intel BX80580Q9400 User Manual - Page 77

Appendix C, Programming System, BIOS Using a Flash Programming, Device

Get Intel BX80580Q9400 - Core 2 Quad 2.66 GHz Processor PDF manuals and user guides
UPC - 735858203074
View all Intel BX80580Q9400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Programming System BIOS Using a Flash Programming Device Appendix C Programming System BIOS Using a Flash Programming Device The BIOS for the development board is in two non-removable flash devices. The flash can be programmed using a bootable DOS device, or through a special BIOS programming device that connects to header J8D2 on the board. One such programming device is the Dediprog SF100 available from the manufacturer at www.dediprog.com. The development board required the use of a 2 partition SPI image for SPI-0 and SPI-1 respectively. The descriptors are stored on SPI-0 while the BIOS is on SPI-1. To program the flash using a flash programming device: 1. Setup the hardware and software of the flash programming device on a host system according to the manufacturer's instructions. 2. Obtain the latest BIOS image (separated into two .bin files). Store the image files on the host system. 3. Disconnect the power supply of the development board. 4. Connect the programming device to the development board at J8D2. 5. Set jumpers J9C1 and J9D1 at 1-2. 6. Set jumper J8C1 at 1-2 for SPI-0. Erase the existing image and flash the .bin image corresponding to SPI-0. 7. Set the jumper J8C1 at 2-3 for SPI-1. Erase the existing image and flash the .bin image corresponding to SPI-1. 8. Once the programming is successful on both the SPI, set J8C1, J9C1 and J9D1 to 1-X. 9. Remove the flash programmer connector from J8D2. 10. Set the jumper J8H1 at 1-X for booting from the SPI § Development Kit User's Manual 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Programming System BIOS Using a Flash Programming Device
Development Kit User’s Manual
77
Appendix C
Programming System
BIOS Using a Flash Programming
Device
The BIOS for the
development board is in two non-removable flash devices.
The
flash can be programmed using a bootable DOS device, or through a special BIOS
programming device that connects to header J8D2 on the board.
One such
programming device is the Dediprog SF100 available from the manufacturer at
www.dediprog.com.
The
development board required the use of a 2 partition SPI image for SPI-0 and
SPI-1 respectively. The descriptors are stored on SPI-0 while the BIOS is on SPI-1.
To program the flash using a flash programming device:
1.
Setup the hardware and software of the flash programming device on a host
system according to the manufacturer’s instructions.
2.
Obtain the latest BIOS image (separated into two .bin files).
Store the image files
on the host system.
3.
Disconnect the power supply of the development board.
4.
Connect the programming device to the development board at J8D2.
5.
Set jumpers J9C1 and J9D1 at 1-2.
6.
Set jumper J8C1 at 1-2 for SPI-0.
Erase the existing image and flash the .bin
image corresponding to SPI-0.
7.
Set the jumper J8C1 at 2-3 for SPI-1.
Erase the existing image and flash the .bin
image corresponding to SPI-1.
8.
Once the programming is successful on both the SPI, set J8C1, J9C1 and J9D1 to
1-X.
9.
Remove the flash programmer connector from J8D2.
10.
Set the jumper J8H1 at 1-X for booting from the SPI
§