Intermec PB50 PB50 and PB51 Mobile Printer User Guide - Page 50

To con the printer to use WPA-PSK or WPA2-PSK mode, can be OFF, LEAP, or TTLS. - admin password

Get Intermec PB50 PDF manuals and user guides View all Intermec PB50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Chapter 2 - Configuring the Mobile Printer To configure the printer to use WPA-PSK or WPA2-PSK mode 1 Send the following commands to log in as an administrator and set the SSID: .x,su -p pass admin ws,SSID,xxxxx where xxxxx can be from 0 to 32 alphanumeric characters. 2 Send one of the following commands to turn on WPA or WPA2 authentication. Send the WPA-PSK or WPA2-PSK command to set a pre-shared key: ws,WPA,ON ws,WPA2,ON ws,WPA_PSK, xxxxxxxxxx where xxxxxxxxxx is a value between 8 and 64 characters. 3 Send the following command to activate the settings: ws,ACTIVE,1 To configure the printer to use WPA or WPA2 Enterprise mode 1 Send the following commands to login as an administrator and set the SSID: .x,su -p pass admin ws,SSID,xxxxx where xxxxx can be from 0 to 32 alphanumeric characters. Note: The default administrator password is "pass." If you have changed the password, use your password instead of "pass." 2 Send one of the following commands to enable WPA-802.1x or WPA2-802.1x authentication. You should also send the WPA_PSK command that does not contain a value: ws,WPA,ON ws,WPA2,ON ws,WPA_PSK, 3 Send these commands to configure the EAP_TYPE: ws,EAP_TYPE,xxxx where xxxx can be OFF, LEAP, PEAP, or TTLS. ws,.EAP_USER,xxxx ws,.EAP_PASS,xxxx 38 PB50 and PB51 Mobile Printer User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Chapter 2 — Configuring the Mobile Printer
38
PB50 and PB51 Mobile Printer User Guide
To configure the printer to use WPA-PSK or WPA2-PSK mode
1
Send the following commands to log in as an administrator and
set the SSID:
<STX><ESC>.x,su -p pass admin<ETX>
<STX><SI>ws,SSID,
xxxxx
<ETX>
where
xxxxx
can be from 0 to 32 alphanumeric characters.
2
Send one of the following commands to turn on WPA or WPA2
authentication. Send the WPA-PSK or WPA2-PSK command to set
a pre-shared key:
<STX><SI>ws,WPA,ON<ETX>
<STX><SI>ws,WPA2,ON<ETX>
<STX><SI>ws,WPA_PSK,
xxxxxxxxxx
<ETX>
where
xxxxxxxxxx
is a value between 8 and 64 characters.
3
Send the following command to activate the settings:
<STX><SI>ws,ACTIVE,1<ETX>
To configure the printer to use WPA or WPA2 Enterprise mode
1
Send the following commands to login as an administrator and set
the SSID:
<STX><ESC>.x,su -p pass admin<ETX>
<STX><SI>ws,SSID,
xxxxx
<ETX>
where
xxxxx
can be from 0 to 32 alphanumeric characters.
2
Send one of the following commands to enable WPA-802.1x or
WPA2-802.1x authentication. You should also send the WPA_PSK
command that does not contain a value:
<STX><SI>ws,WPA,ON<ETX>
<STX><SI>ws,WPA2,ON<ETX>
<STX><SI>ws,WPA_PSK, <ETX>
3
Send these commands to configure the EAP_TYPE:
<STX><SI>ws,EAP_TYPE,
xxxx
<ETX>
where
xxxx
can be OFF, LEAP, PEAP, or TTLS.
<STX><SI>ws,.EAP_USER,
xxxx
<ETX>
<STX><SI>ws,.EAP_PASS,
xxxx
<ETX>
Note:
The default administrator password is “pass.” If you have
changed the password, use your password instead of “pass.”