Invacare 9XT Owners Manual - Page 56

Rear Wheels

Get Invacare 9XT PDF manuals and user guides View all Invacare 9XT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

8 REAR WHEELS 1. Push in the detent pin of quick-release axle (with wheel) and pull the axle out through the opening in the center of the rear wheel and axle spacer.  Axle spacer is used only if wheelchair is equipped with conventional arms. 2. Push in the detent pin of the quick-release axle again and pull the axle out of the rear wheel. 3. Repeat STEPS 1-2 for the opposite rear wheel. 4. To reinstall the rear wheel onto the wheelchair, reverse STEPS 1-3.  Make sure axle spacer is between rear wheel and wheelchair frame if wheelchair is equipped with conventional arms. ƽ WARNING Make sure the detent pin and detent balls of the quick-release axle are fully released before operating the wheelchair. The detent balls MUST be protruding past the inside of the rear wheel axle bushing for a positive lock (Detail "A"). Keep detent balls clean. Invacare recommends inserting quick-release axles with the detent pin to the inside of the wheelchair to prevent accidental release during contact activities. 5. If the detent balls are not protruding past the inside of the axle bushing or there is too much side-to-side movement of the rear wheel assembly, refer to Adjusting Quick-Release Axle on page 58. Invacare® 9000 Series Wheelchair 56 Part No. 1056953

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
8
REAR WHEELS
Invacare® 9000 Series Wheelchair
56
Part No. 1056953
1.
Push in the detent pin of quick-release axle (with wheel) and pull the axle out through the opening in the center of the rear wheel and axle spacer.
2.
Push in the detent pin of the quick-release axle again and pull the axle out of the rear wheel.
3.
Repeat STEPS 1-2 for the opposite rear wheel.
4.
To reinstall the rear wheel onto the wheelchair, reverse STEPS 1-3.
5.
If the detent balls are not protruding past the inside of the axle bushing or there is too much side-to-side movement of the rear wheel assembly,
refer to Adjusting Quick-Release Axle
on page 58.
Axle spacer is used only if wheelchair is equipped with conventional arms.
Make sure axle spacer is between rear wheel and wheelchair frame if wheelchair is equipped with conventional arms.
±
WARNING
Make sure the detent pin and detent balls of the quick-release axle are fully released before operating the wheelchair.
The detent balls MUST be protruding past the inside of the rear wheel axle bushing for a positive lock (Detail "A").
Keep detent balls clean.
Invacare recommends inserting quick-release axles with the detent pin to the inside of the wheelchair to prevent accidental
release during contact activities.