Invacare 9XT Owners Manual - Page 67

Any wheel lock adjustment should embed the wheel lock shoe at least 1/8-inch 3/16-inch if pneumatic

Get Invacare 9XT PDF manuals and user guides View all Invacare 9XT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

5. Engage the wheel lock. 10 ANTI-TIPPERS/WHEEL LOCKS 6. Measure the distance the wheel lock is embedded into the tire as shown in FIGURE 4 on page 68.  Any wheel lock adjustment should embed the wheel lock shoe at least 1/8-inch (3/16-inch if pneumatic tire) into the tire when engaged. 7. Repeat STEPS 1-6 until the wheel lock shoe embeds the tire 1/8-inch (3/16-inch for pneumatic tires) and holds the occupied wheelchair in place when pushed. 8. If the measurement of 1/8-inch (3/16-inch for pneumatic tires) can not be achieved, Perform one of the following: • Bolt-on wheel locks - Remove the bolt and locknut that secure the wheel lock to the wheelchair frame and mount the wheel lock in the remaining mounting position. • Clamp-on Wheel locks - Proceed to STEP 9. 9. If wheel lock is unable to properly engage the wheel it may be necessary to install wheel lock shoe extensions. Refer to Installing Wheel Lock Shoe Extensions on page 69. 10. Repeat STEPS 1-9 for the opposite wheel lock. 11. Engage both wheel locks and ensure the occupied wheelchair is held in place when pushed. ƽ WARNING If wheel locks DO NOT hold the occupied wheelchair in place, contact a qualified technician. Otherwise injury or damage may occur. Part No. 1056953 67 Invacare® 9000 Series Wheelchair

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
10
ANTI-TIPPERS/WHEEL LOCKS
Part No. 1056953
67
Invacare® 9000 Series Wheelchair
5.
Engage the wheel lock.
6.
Measure the distance the wheel lock is embedded into the tire as shown in FIGURE 4 on page 68.
7.
Repeat STEPS 1-6 until the wheel lock shoe embeds the tire 1/8-inch (3/16-inch for pneumatic tires) and holds the occupied wheelchair in place
when pushed.
8.
If the measurement of 1/8-inch (3/16-inch for pneumatic tires) can not be achieved, Perform one of the following:
•
Bolt-on wheel locks -
Remove the bolt and locknut that secure the wheel lock to the wheelchair frame and mount the wheel lock in the
remaining mounting position.
•
Clamp-on Wheel locks - Proceed to STEP 9.
9.
If wheel lock is unable to properly engage the wheel it may be necessary to install wheel lock shoe extensions. Refer to Installing Wheel Lock
Shoe Extensions
on page 69.
10.
Repeat STEPS 1-9 for the opposite wheel lock.
11.
Engage both wheel locks and ensure the occupied wheelchair is held in place when pushed.
Any wheel lock adjustment should embed the wheel lock shoe at least 1/8-inch (3/16-inch if pneumatic tire) into the tire
when engaged.
±
WARNING
If wheel locks DO NOT hold the occupied wheelchair in place, contact a qualified technician. Otherwise injury or damage
may occur.