Invacare IFX-20MP Owners Manual - Page 83

Removing/Installing the Front Shroud Assembly, Fig. 10-7 Connect the Rear Battery

Page 83 highlights

3. Install the front shroud. Refer to 10.4.2 Removing/Installing the Front Shroud Assembly, page 77. 4. Slide the rear battery R into the battery box with the connector towards the rear of the wheelchair. 10 Service 7. Lift up and install the battery door assembly onto the battery box. Ensure the hooks on the battery box are seated properly in the slots on the battery box door. The power module P and GTRAC module W will remain attached to the battery door assembly during this procedure. 8. Install the two bolts M to secure the battery door assembly N to the rear of the battery box O. Torque to 90 in-lbs (7.5 ft-lbs, 10 Nm). Fig. 10-7 Connect the Rear Battery 5. Connect the rear battery harness (red handle) Q. 6. Lift the battery door assembly N with power module P and attached cables over the right rear swingarm and position it at the rear of the battery box. 60101916-A 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108

3.
Install the front shroud. Refer to
10.4.2
Removing/Installing the Front Shroud Assembly, page 77
.
4. Slide the rear battery
R
into the battery box with the
connector towards the rear of the wheelchair.
Fig. 10-7 Connect the Rear Battery
5.
Connect the rear battery harness (red handle)
Q
.
6.
Lift the battery door assembly
N
with power module
P
and attached cables over the right rear swingarm and
position it at the rear of the battery box.
7.
Lift up and install the battery door assembly onto the
battery box.
Ensure the hooks on the battery box are seated
properly in the slots on the battery box door.
The power module
P
and GTRAC module
W
will
remain attached to the battery door assembly
during this procedure.
8. Install the two bolts
M
to secure the battery door assembly
N
to the rear of the battery box
O
. Torque to 90 in-lbs (7.5
ft-lbs, 10 Nm).
60101916-A
83
10 Service