Lantronix xPico xPico - Integration Guide - Page 20

Reverse-SMA to U.FLlong P/N 500-180-R, U.FL to U.FL Cable P/N 500-181-R, Antenna Type

Get Lantronix xPico PDF manuals and user guides View all Lantronix xPico manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

2: Functional Description Table 2-5 xPico Wi-Fi External Antenna Options Antenna Type PCB Strip Antenna with 50mm cable to U.FL connector With tape backing PCB Strip Antenna with 50mm cable to U.FL connector Without tape backing Swivel type antenna, with RP-SMA(M) connector Peak Gain Typical 1.5 to 2.5dBi, 2.39 Ghz to 2.49 Ghz 1.5 to 2.5dBi, 2.39 Ghz to 2.49 Ghz 2 dBi, 2.4 Ghz to 2.5 Ghz, 2 dBi, 5.15 Ghz to 5.85 Ghz Lantronix Part Number Vendor Ethertronics® Vendor Part Number 1001077 Ethertronics 1000668 930-033-RACC 50 piece bulk pack Wanshih WSS002 Note: The PCB strip antenna is available from Ethertronics with or without adhesive tape backing for mounting to a plastic case. For the component without tape backing a non-conductive double sided adhesive tape can be used to fix the antenna in place. The Ethertronics part numbers listed above come with a 50mm U.FL cable attached to the PCB strip antenna. The 50mm cable length is the minimum allowed cable length for use with the xPico Wi-Fi embedded device server. For similar PCB strip antennas with longer cables consult with Ethertronics (www.ethertronics.com). Lantronix provides a U.FL to Reverse SMA antenna cable in with the evaluation board and sample kits for development work. These cables can be purchased from Lantronix for production or supplied by an RF cable manufacturer. External antennas can be purchased from the antenna vendor. Components for cable design should be selected for low loss over the entire 2.4Ghz to 5.9Ghz signal range. The cable target impedence should be 50 ohms. Figure 2-4 Reverse-SMA to U.FL(long) (P/N 500-180-R) Figure 2-5 U.FL to U.FL Cable (P/N 500-181-R) xPico® Embedded Device Server Integration Guide 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
2: Functional Description
Table 2-5
xPico Wi-Fi External Antenna Options
Antenna Type
Peak Gain Typical
Lantronix
Part
Number
Vendor
Vendor
Part
Number
PCB Strip Antenna with
50mm cable to U.FL
connector
With tape backing
1.5 to 2.5dBi, 2.39 Ghz
to 2.49 Ghz
Ethertronics®
1001077
PCB Strip Antenna with
50mm cable to U.FL
connector
Without tape backing
1.5 to 2.5dBi, 2.39 Ghz
to 2.49 Ghz
Ethertronics
1000668
Swivel type antenna,
with RP-SMA(M)
connector
2 dBi, 2.4 Ghz to 2.5
Ghz, 2 dBi, 5.15 Ghz to
5.85 Ghz
930-033-R-
ACC
50 piece
bulk pack
Wanshih
WSS002
Note:
The PCB strip antenna is available from Ethertronics with or without
adhesive tape backing for mounting to a plastic case.
For the component without
tape backing a non-conductive double sided adhesive tape can be used to fix the
antenna in place.
The Ethertronics part numbers listed above come with a 50mm
U.FL cable attached to the PCB strip antenna.
The 50mm cable length is the
minimum allowed cable length for use with the xPico Wi-Fi embedded device
server.
For similar PCB strip antennas with longer cables consult with
Ethertronics (www.ethertronics.com).
Lantronix provides a U.FL to Reverse SMA antenna cable in with the evaluation board
and sample kits for development work.
These cables can be purchased from Lantronix
for production or supplied by an RF cable manufacturer.
External antennas can be
purchased from the antenna vendor.
Components for cable design should be selected
for low loss over the entire 2.4Ghz to 5.9Ghz signal range.
The cable target impedence
should be 50 ohms.
Figure 2-4
Reverse-SMA to U.FL(long) (P/N 500-180-R)
Figure 2-5
U.FL to U.FL Cable (P/N 500-181-R)
xPico® Embedded Device Server Integration Guide
20