Lantronix xPico xPico - Integration Guide - Page 34

To Install the xPico or xPico Wi-Fi Module

Get Lantronix xPico PDF manuals and user guides View all Lantronix xPico manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

3: Mounting Instructions and PCB Footprint To Install the xPico or xPico Wi-Fi Module In the xPico Development Kit (Part Number XPC100100K-02) and xPico Wi-Fi Development Kit (XPW100100K-01), the xPico module comes installed to the xPico Evaluation Board via the connector J1 (Hirose component). If ordered separately, you may need to install it by following the directions below. The included white Mounting Quick Clip is used to align and fasten the module to the evaluation board. Note: Refer to the Notification: Soldering Profile and Washing instruction located at http://www.lantronix.com/support/downloads/. This document is located under the xPico Wi-Fi product line. 1. Place the module into the white mounting clip, lining up the clip legs and the four module grooves so that the module is seated inside the white clip. For xPico Wi-Fi connect the RF cable to the module U.FL connector prior to installing the Quick Clip. White Mounting Clip xPico/xPico Wi-Fi Module 2. Push the legs of the white clip inward to secure the module to the clip. Module/Mounting Clip Combination 3. Flip over the module/mounting clip combination so that the product label displays on top and the white mounting clip legs are pointed downward. 4. For XPico Wi-Fi embedded device server high temperature operation, above +70C, it is recommended to place a heat pad between the module and the adjacent PCB. The recommended heat pad is Lantronix part number XPC100A002-01-B (available in a 50 piece bulk pack). 5. Place the module/mounting clip combination so that the four mounting clip legs align with the four standoff holes on the board surrounding the J1 connector (see Figure 3-2). Make sure to properly orientate the module/mounting clip combination on the board, so that the J1 connector/Hirose component is properly aligned. xPico® Embedded Device Server Integration Guide 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
3: Mounting Instructions and PCB Footprint
To Install the xPico or xPico Wi-Fi Module
In the xPico Development Kit (Part Number XPC100100K-02) and xPico Wi-Fi
Development Kit (XPW100100K-01), the xPico module comes installed to the xPico
Evaluation Board via the connector J1 (Hirose component).
If ordered separately, you
may need to install it by following the directions below.
The included white Mounting
Quick Clip is used to align and fasten the module to the evaluation board.
Note:
Refer to the Notification: Soldering Profile and Washing instruction located
at
This document is located under
the xPico Wi-Fi product line.
1. Place the module into the white mounting clip, lining up the clip legs and the four
module grooves so that the module is seated inside the white clip.
For xPico Wi-Fi
connect the RF cable to the module U.FL connector prior to installing the Quick Clip.
2. Push the legs of the white clip inward to secure the module to the clip.
3. Flip over the module/mounting clip combination so that the product label displays on
top and the white mounting clip legs are pointed downward.
4. For XPico Wi-Fi embedded device server high temperature operation, above +70C, it
is recommended to place a heat pad between the module and the adjacent PCB.
The
recommended heat pad is Lantronix part number XPC100A002-01-B (available in a 50
piece bulk pack).
5. Place the module/mounting clip combination so that the four mounting clip legs align
with the four standoff holes on the board surrounding the J1 connector
(see
Figure 3-2
).
Make sure to properly orientate the module/mounting clip
combination on the board, so that the J1 connector/Hirose component is properly
aligned.
Module/Mounting
Clip Combination
White
Mounting Clip
xPico/xPico Wi-Fi
Module
xPico® Embedded Device Server Integration Guide
34