Lenovo Ispirati 2001 User's Guide - Ispirati 2001 (6300) (English) - Page 29

Earphone and Mic In Header JAUDIO

Get Lenovo Ispirati 2001 PDF manuals and user guides View all Lenovo Ispirati 2001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

3-4 Chapter 3: Motherboard Connectors &"USB Header (JUSB2) This is an onboard extension 2x6 pin header for connection to two front USB ports. &"Earphone and Mic In Header (JAUDIO) This onboard connector enables front access microphone and headphone connections. &"Primary IDE Connector (JIDE1) Used to connect the ATA-66 EIDE hard drive via an 80 wire 40-pin ribbon cable. &"Secondary IDE Connector (JIDE2) Used to connect the ATA-33 CD-ROM / CD-RW / DVD drive via a 40-pinregular ribbon cable. &"Floppy Disk Connector (FDD) Onboard floppy disk connector for a customer installable Floppy Drive. Used with an internal floppy drive ribbon cable to connect to an internal floppy drive. &"Front Panel Connector (JFP1) Front panel connector includes headers for power switch, power/suspend LED, and hard drive LED. A proprietary cable is used to connect this to the front panel board. %"Power button signal - Pressing the power switch for more than 4 seconds will force the system to turn off. At least two seconds must pass before the power supply will recognize another on/off signal. To put the system in suspend mode, APM should be enabled in BIOS Setup and APM driver of the operating system should be loaded. %"Power/Suspend LED - This LED stays on when the computer is in full power mode, it turns to amber when the computer is in suspend mode. %"Hard Drive LED - This LED provides a visual indicator that data is being read from or written to an IDE hard drive. For the LED to function properly, the IDE drive must be connected to the onboard IDE controller. When HDD is idle, this LED is off, when it is active, this LED lights up.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
3-4
Chapter 3: Motherboard Connectors
&
USB Header (JUSB2)
This is an onboard extension 2x6 pin header for connection to two front USB ports.
&
Earphone and Mic In Header (JAUDIO)
This onboard connector enables front access microphone and headphone
connections.
&
Primary IDE Connector (JIDE1)
Used to connect the ATA-66 EIDE hard drive via an 80 wire 40-pin ribbon cable.
&
Secondary IDE Connector (JIDE2)
Used to connect the ATA-33 CD-ROM / CD-RW / DVD drive via a 40-pinregular
ribbon cable.
&
Floppy Disk Connector (FDD)
Onboard floppy disk connector for a customer installable Floppy Drive. Used with
an internal floppy drive ribbon cable to connect to an internal floppy drive.
&
Front Panel Connector (JFP1)
Front panel connector includes headers for power switch, power/suspend LED,
and hard drive LED. A proprietary cable is used to connect this to the front panel
board.
%
Power button signal – Pressing the power switch for more than 4 seconds will
force the system to turn off.
At least two seconds must pass before the power
supply will recognize another on/off signal. To put the system in suspend mode,
APM should be enabled in BIOS Setup and APM driver of the operating system
should be loaded.
%
Power/Suspend LED – This LED stays on when the computer is in full power
mode, it turns to amber when the computer is in suspend mode.
%
Hard Drive LED – This LED provides a visual indicator that data is being read
from or written to an IDE hard drive. For the LED to function properly, the IDE
drive must be connected to the onboard IDE controller.
When HDD is idle, this
LED is off, when it is active, this LED lights up.