Lenovo NetVista Hardware Maintenance Manual for NetVista 6266, 6270, 6276, 627 - Page 51

BIOS Error Codes, Messages, beeps, Action/FRU, CTRL-ALT

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Messages, Action/FRU beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause. 201 Memory test failure. 301 Keyboard error or no keyboard present. Insert the memory modules in the DIMM sockets properly, and then reboot the system. Memory module. See the "Step 005" of "Memory" on page 64 to replace memory module. System board. Make sure the keyboard is connected properly and are set correctly in BIOS Setup. System board. 662 Unable to reset floppy subsystem. FLOPPY DISK(S) failure (80) 662 Floppy Type mismatch. FLOPPY DISK(S) failure (40) 1701 Make sure the hard disks are set correctly in BIOS setup. Hard disk(s) Diagnosis failure Hard disk drive cable/connection. Hard disk drive. System board. 1762 Make sure that the System Boot Drive parameter in the Startup Primary master IDE has changed Options of BIOS Setup is not set to [Drive A only]. Primary slave IDE has changed Load default settings in Setup. Secondary master IDE has Insert a system diskette into diskette drive and reboot system. changed Make sure the diskette drive configuration setting in BIOS Setup is Secondary slave IDE has correct. changed Hard disk drive power. 1780 Primary master hard disk failure Diskette drive. System board. A warning message to indicate there has been a change of IDE Primary (Secondary) Channel Master (Slave) device. Load default settings in Setup. 1781 Primary slave hard disk failure Check IDE drive jumper. See "3.5-In. Hard Disk Drive Jumper Locations" on page 107. IDE drive power. 1782 Secondary master hard disk failure IDE drive cable/connection. IDE drive. A warning message to indicate there has been a change of IDE Primary (Secondary) Channel Master (Slave) device. Load default settings in Setup. Check IDE drive jumper. See "3.5-In. Hard Disk Drive Jumper 1783 Locations" on page107. Secondary slave hard disk failure IDE drive power. IDE drive cable/connection. IDE drive. 8602 Make sure the Mouse is connected properly and is set up correctly in Mouse error on no Mouse present BIOS Setup. Mouse. System board. SYSTEM HALTED, (CTRL-ALT- Indicates the present boot attempt has been aborted and the system DEL) TO REBOOT... must be rebooted. Press and hold down the CTRL and ALT key and DEL. Hard Disk(s) failure (80) Hard Disk Drive reset failed. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
51
Table 2-1 BIOS Error Codes, Messages, and Beeps List
BIOS Error Codes, Messages,
beeps
Action/FRU
NOTE:
To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If
directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure
is indicated, the first Action/FRU listed in right column is the most likely cause.
201
Memory test failure.
Insert the memory modules in the DIMM sockets properly, and then
reboot the system.
Memory module. See the “Step 005” of ”Memory” on page 64 to
replace memory module.
System board.
301
Keyboard error or no keyboard
present.
Make sure the keyboard is connected properly and are set correctly in
BIOS Setup.
System board.
662
FLOPPY DISK(S) failure (80)
Unable to reset floppy subsystem.
662
FLOPPY DISK(S) failure (40)
Floppy Type mismatch.
1701
Hard disk(s) Diagnosis failure
Make sure the hard disks are set correctly in BIOS setup.
Hard disk drive cable/connection.
Hard disk drive.
System board.
1762
Primary master IDE has changed
Primary slave IDE has changed
Secondary master IDE has
changed
Secondary slave IDE has
changed
Make sure that the System Boot Drive parameter in the Startup
Options of BIOS Setup is not set to [Drive A only].
Load default settings in Setup.
Insert a system diskette into diskette drive and reboot system.
Make sure the diskette drive configuration setting in BIOS Setup is
correct.
Hard disk drive power.
Diskette drive.
System board.
1780
Primary master hard disk failure
1781
Primary slave hard disk failure
A warning message to indicate there has been a change of IDE
Primary (Secondary) Channel Master (Slave) device.
Load default settings in Setup.
Check IDE drive jumper. See “3.5-In. Hard Disk Drive Jumper
Locations” on page 107.
IDE drive power.
IDE drive cable/connection.
IDE drive.
1782
Secondary master hard disk
failure
1783
Secondary slave hard disk failure
A warning message to indicate there has been a change of IDE
Primary (Secondary) Channel Master (Slave) device.
Load default settings in Setup.
Check IDE drive jumper. See ”3.5-In. Hard Disk Drive Jumper
Locations” on page107.
IDE drive power.
IDE drive cable/connection.
IDE drive.
8602
Mouse error on no Mouse present
Make sure the Mouse is connected properly and is set up correctly in
BIOS Setup.
Mouse.
System board.
SYSTEM HALTED, (
CTRL-ALT-
DEL
) TO REBOOT…
Indicates the present boot attempt has been aborted and the system
must be rebooted. Press and hold down the
CTRL
and
ALT
key and
DEL
.
Hard Disk(s) failure (80)
Hard Disk Drive reset failed.