Lenovo NetVista Hardware Maintenance Manual for NetVista 6266, 6270, 6276, 627 - Page 61

Factory-Installed Modem Card, DOES THE MODEM PASS THE TEST? YES, READ AHEAD. NO, GO TO STEP 004.

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Factory-Installed Modem Card 001 - START Power off the system unit. In Windows 98 Device Manager, make sure that the modem is not configured with a conflicting COM port and IRQ setting. Make sure that the communication software is configured with the correct COM and IRQ settings ( same COM port and IRQ as the modem). Make sure that all communication parameters (baud rate, data, stop and parity bits) are properly configured and are identical on both sides. Connect the phone line to the LINE port of the modem card. NOTE: Check the outside phone line by connecting a working telephone to the telephone wall jack. Listen for a dial tone to ensure that the phone line is good. 002 Insert the diagnostics diskette into the diskette drive. Power on the system unit. Select Diagnostics menu, Select All Tests, then execute Modem test. 003 - DOES THE MODEM PASS THE TEST? (YES, READ AHEAD. NO, GO TO STEP 004.) Power off the system unit. Remove all adapter cards. Connect a hard disk drive with pre-loaded Windows 98. Power on the system unit. Perform the following steps under Windows 98. NOTE: If an operating system other than Microsoft Windows 98 is installed, the program screens and icons may differ from these instructions. 1. Start Microsoft Windows 98. 2. Select the Start icon. 3. Select Program, then select Accessories, Hyper Terminal. 4. Select an on-line service station, dial and connect to it. 004 - CAN THE MODEM DIAL OUT AND CONNECT TO ANY BBS SUCCESSFULLY? (YES, READ AHEAD. NO, GO TO STEP 005.) The modem adapter functions normally. End. 005 Make sure that Windows 98 is properly installed, and then power off the system unit. Plug the modem adapter card into a different PCI slot. Go to step 002. If the error symptom still remains, replace the modem adapter card. End. 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
61
Factory-Installed Modem Card
001 - START
±
Power off the system unit.
±
In Windows 98 Device Manager, make sure that the modem is not configured with a conflicting COM port and IRQ setting.
±
Make sure that the communication software is configured with the correct COM and IRQ settings ( same COM port and IRQ as the
modem).
±
Make sure that all communication parameters (baud rate, data, stop and parity bits) are properly configured and are identical on both
sides.
±
Connect the phone line to the LINE port of the modem card.
NOTE:
Check the outside phone line by connecting a working telephone to the telephone wall jack. Listen for a dial tone to ensure
that the phone line is good.
002 -
±
Insert the diagnostics diskette into the diskette drive.
±
Power on the system unit.
±
Select
Diagnostics
menu,
±
Select
All Tests,
then execute
Modem
test.
003 -
DOES THE MODEM PASS THE TEST? (YES, READ AHEAD. NO, GO TO STEP 004.)
±
Power off the system unit.
±
Remove all adapter cards.
±
Connect a hard disk drive with pre-loaded Windows 98.
±
Power on the system unit.
±
Perform the following steps under Windows 98.
NOTE:
If an operating system other than Microsoft Windows 98 is installed, the program screens and icons may differ from these
instructions.
±
1. Start Microsoft Windows 98.
±
2. Select the
Start
icon.
±
3. Select
Program
, then select
Accessories
,
Hyper Terminal
.
±
4. Select an
on-line service station
, dial and connect to it.
004 -
CAN THE MODEM DIAL OUT AND CONNECT TO ANY BBS SUCCESSFULLY? (YES, READ AHEAD. NO, GO TO STEP 005.)
±
The modem adapter functions normally.
±
End.
005 -
±
Make sure that Windows 98 is properly installed, and then power off the system unit.
±
Plug the modem adapter card into a different PCI slot.
±
Go to step 002.
±
If the error symptom still remains, replace the modem adapter card.
±
End.