Lenovo ThinkServer RD240 (English) Installation and User Guide - Page 49

Installing the riser card assembly, it is completely removed from the slot.

Get Lenovo ThinkServer RD240 PDF manuals and user guides View all Lenovo ThinkServer RD240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

4. Loosen the retaining screws on the front and rear of the riser card assembly. Then, remove the riser card assembly from the server. Note: If the riser card assembly is secured in place by a retaining latch 1 , press the retaining latch to release the riser card assembly from the latch. Then, carefully pull the riser card assembly out of the slot. If necessary, alternate moving each side of the riser card assembly a small and equal amount until it is completely removed from the slot. Figure 26. Removing the riser card assembly What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the removal procedure, go to "Completing the parts replacement" on page 71. Installing the riser card assembly Attention: Do not open your server or attempt any repair before reading and understanding the "Safety information" on page iii and "Guidelines" on page 19. Chapter 5. Installing, removing, or replacing hardware 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
4. Loosen the retaining screws on the front and rear of the riser card assembly. Then, remove the riser
card assembly from the server.
Note:
If the riser card assembly is secured in place by a retaining latch
1
, press the retaining latch to
release the riser card assembly from the latch. Then, carefully pull the riser card assembly out of the
slot. If necessary, alternate moving each side of the riser card assembly a small and equal amount until
it is completely removed from the slot.
Figure 26. Removing the riser card assembly
What to do next:
•
To work with another piece of hardware, go to the appropriate section.
•
To complete the removal procedure, go to “Completing the parts replacement” on page 71.
Installing the riser card assembly
Attention:
Do not open your server or attempt any repair before reading and understanding the “Safety information”
on page iii and “Guidelines” on page 19.
Chapter 5
.
Installing, removing, or replacing hardware
37