Lenovo ThinkServer RD240 (English) Installation and User Guide - Page 63

and then firmly insert the RAID controller

Get Lenovo ThinkServer RD240 PDF manuals and user guides View all Lenovo ThinkServer RD240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

c. Hold the battery card assembly with the battery side up and the J5 board-to-board connector lining up with the J10 BBU connector 1 on the RAID controller. Carefully press the battery card assembly onto the RAID controller so that the two connectors are firmly joined. Then, secure the battery card assembly to the RAID controller with the three screws and the standoffs that come with the battery card assembly accessory kit. Figure 42. Installing the battery card assembly onto the RAID controller 1 J10 BBU connector 6. Connect one end of the mini SAS signal cable to the RAID controller. Note: Use the two 400 mm (15.75 inches) mini SAS signal cables. Figure 43. Connecting the mini SAS signal cables to the RAID controller 1 Ports 0-3 2 Ports 4-7 a. For one mini SAS signal cable, connect the end to the ports 0-3 on the RAID controller. b. For the other mini SAS signal cable, connect the end to the ports 4-7 on the RAID controller. 7. Position the RAID controller near the riser card assembly. Ensure that the left edge of the RAID controller is inserted into the notch of the RAID card retention bracket 1 , and then firmly insert the RAID controller straight down into the PCI card slot 1 2 until it is securely seated. Then install the screw 3 to secure the RAID controller. Chapter 5. Installing, removing, or replacing hardware 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
c.
Hold the battery card assembly with the battery side up and the J5 board-to-board connector
lining up with the J10 BBU connector
1
on the RAID controller. Carefully press the battery card
assembly onto the RAID controller so that the two connectors are firmly joined. Then, secure the
battery card assembly to the RAID controller with the three screws and the standoffs that come
with the battery card assembly accessory kit.
Figure 42. Installing the battery card assembly onto the RAID controller
1
J10 BBU connector
6. Connect one end of the mini SAS signal cable to the RAID controller.
Note:
Use the two 400 mm (15.75 inches) mini SAS signal cables.
Figure 43. Connecting the mini SAS signal cables to the RAID controller
1
Ports 0-3
2
Ports 4-7
a.
For one mini SAS signal cable, connect the end to the ports 0-3 on the RAID controller.
b. For the other mini SAS signal cable, connect the end to the ports 4-7 on the RAID controller.
7. Position the RAID controller near the riser card assembly. Ensure that the left edge of the RAID controller
is inserted into the notch of the RAID card retention bracket
1
, and then firmly insert the RAID controller
straight down into the PCI card slot 1
2
until it is securely seated. Then install the screw
3
to secure the
RAID controller.
Chapter 5
.
Installing, removing, or replacing hardware
51