Lenovo ThinkServer RD240 (English) Installation and User Guide - Page 91

USB Mass Storage Device Configuration

Get Lenovo ThinkServer RD240 PDF manuals and user guides View all Lenovo ThinkServer RD240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Table 14. Submenus under the Mass Storage Controller Configuration Item SATA Configuration Option Disabled / [Enabled] Description Enable or disable the integrated SATA controller. Configure SATA as [IDE] / RAID To select the hard disk drive mode. If this option is set to IDE, all the SATA connectors will be configured as stand-alone SATA connectors. Notes: 1. The settings in [ ] are the default settings in the Setup Utility program. 2. The SATA Configuration item might not apply because your server came with an integrated SAS controller. Table 15. Submenus under the SuperIO Configuration Item Option Serial Port1 Address Disabled; [3F8/IRQ4]; 3E8/IRQ4; 2E8/IRQ3 Serial Port2 Address Disabled; [2F8/IRQ3]; 3E8/IRQ4; 2E8/IRQ3 Note: The settings in [ ] are the default settings in the Setup Utility program. Description Select the I/O base address and interrupt for serial port 1. Select the I/O base address and interrupt for serial port 2. Table 16. Submenus under the USB Configuration Item Option Description Legacy USB Support Disabled / [Enabled] / Auto Enable or disable the support on legacy USB devices. USB 2.0 Controller Mode FullSpeed / [HiSpeed] Select the USB speed. Hotplug USB FDD Support Disabled / Enabled / [Auto] Enable or disable the support on the hot-swap USB diskette drive. Note: The settings in [ ] are the default settings in the Setup Utility program. For external USB devices, the USB Mass Storage Device Configuration submenu is as below: Emulation Type [Auto] / Floppy / Forced FDD / Hard Select the type of the USB device. Disk / CDROM Chapter 6. Configuring the server 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Table 14. Submenus under the
Mass Storage Controller Configuration
Item
Option
Description
SATA Configuration
Disabled / [Enabled]
Enable or disable the integrated SATA
controller.
Configure SATA as
[IDE] / RAID
To select the hard disk drive mode.
If this option is set to
IDE
, all the
SATA connectors will be configured
as stand-alone SATA connectors.
Notes:
1. The settings in [ ] are the default settings in the Setup Utility program.
2. The
SATA Configuration
item might not apply because your server came with an integrated SAS controller.
Table 15. Submenus under the
SuperIO Configuration
Item
Option
Description
Serial Port1 Address
Disabled; [3F8/IRQ4]; 3E8/IRQ4;
2E8/IRQ3
Select the I/O base address and
interrupt for serial port 1.
Serial Port2 Address
Disabled; [2F8/IRQ3]; 3E8/IRQ4;
2E8/IRQ3
Select the I/O base address and
interrupt for serial port 2.
Note:
The settings in [ ] are the default settings in the Setup Utility program.
Table 16. Submenus under the
USB Configuration
Item
Option
Description
Legacy USB Support
Disabled / [Enabled] / Auto
Enable or disable the support on
legacy USB devices.
USB 2.0 Controller Mode
FullSpeed / [HiSpeed]
Select the USB speed.
Hotplug USB FDD Support
Disabled / Enabled / [Auto]
Enable or disable the support on the
hot-swap USB diskette drive.
Note:
The settings in [ ] are the default settings in the Setup Utility program.
For external USB devices, the
USB Mass Storage Device Configuration
submenu is as below:
Emulation Type
[Auto] / Floppy / Forced FDD / Hard
Disk / CDROM
Select the type of the USB device.
Chapter 6
.
Configuring the server
79