Lenovo ThinkStation C20 (English) User Guide - Page 21

Removing and reinstalling the PCI card holder

Get Lenovo ThinkStation C20 PDF manuals and user guides View all Lenovo ThinkStation C20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

3. Remove the front bezel by releasing the two plastic tabs on the left side and pivoting the front bezel outward. Figure 7. Removing the front bezel 4. Lay the front bezel on a flat surface. 5. To reinstall the front bezel, align the other three plastic tabs on the right side of the front bezel with the corresponding holes in the chassis, then pivot the front bezel inward until it snaps into position. Removing and reinstalling the PCI card holder Attention: Do not open your computer or attempt any repair before reading and understanding the "Important safety information" in the ThinkStation Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkStation Safety and Warranty Guide, go to: http://support.lenovo.com This section provides instructions on how to remove and reinstall the PCI card holder. To remove and reinstall the PCI card holder, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See "Removing the computer cover" on page 13. 3. Remove the front bezel. See "Removing and reinstalling the front bezel" on page 14. 4. Lay the computer on its side. Chapter 2. Installing or replacing hardware 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
3. Remove the front bezel by releasing the two plastic tabs on the left side and pivoting the front bezel
outward.
Figure 7. Removing the front bezel
4. Lay the front bezel on a flat surface.
5. To reinstall the front bezel, align the other three plastic tabs on the right side of the front bezel with the
corresponding holes in the chassis, then pivot the front bezel inward until it snaps into position.
Removing and reinstalling the PCI card holder
Attention:
Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the
ThinkStation Safety and Warranty Guide
that came with your computer. To obtain a copy of the
ThinkStation
Safety and Warranty Guide
, go to:
This section provides instructions on how to remove and reinstall the PCI card holder.
To remove and reinstall the PCI card holder, do the following:
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
2. Remove the computer cover. See “Removing the computer cover” on page 13.
3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 14.
4. Lay the computer on its side.
Chapter 2
.
Installing or replacing hardware
15