Netgear GA311 GA311 User Manual - Page 15

Installation Order, Basic Installation Instructions - driver xp

Get Netgear GA311 - Gigabit PCI Adapter PDF manuals and user guides
UPC - 606449033274
View all Netgear GA311 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

NETGEAR 10/100/1000 Mbps Gigabit Ethernet Adapter GA311 User Manual Note: 1000BASE-T signaling requires four twisted pairs of Category 5 balanced cabling, as specified in ISO/IEC 11801:1995 and ANSI/EIA/TIA-568-A (1995) and tested using procedures defined in TIA/EIA TSB95. Installation Order 1. First, install the GA311 driver and utility software using the setup.exe program on the NETGEAR 10/100/1000 Mbps Gigabit Ethernet Adapter GA311 Resource CD. 2. When the Windows system boots up after installing the GA311 Gigabit Ethernet Adapter, the system automatically detects the new hardware and prompts you to install the driver software for the device. 3. Follow the prompts of the Found New Hardware Wizard to automatically use the driver installed in step 1. If you are installing more than one GA311 Gigabit Ethernet Adapter, you must perform the following procedure for each card. Basic Installation Instructions Use the procedure below that corresponds to the version of Windows you are using: • Windows Vista • Windows XP, 2000, 98SE 2nd edition, or Me • Windows NT 4.0 2-3 v1.0, February 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
NETGEAR 10/100/1000 Mbps Gigabit Ethernet Adapter GA311 User Manual
2-3
v1.0, February 2007
Installation Order
1.
First, install the GA311 driver and utility software using the setup.exe program on the
NETGEAR 10/100/1000 Mbps Gigabit Ethernet Adapter GA311 Resource CD
.
2.
When the Windows system boots up after installing the GA311 Gigabit Ethernet Adapter, the
system automatically detects the new hardware and prompts you to install the driver software
for the device.
3.
Follow the prompts of the Found New Hardware Wizard to automatically use the driver
installed in step 1.
If you are installing more than one GA311 Gigabit Ethernet Adapter, you must perform the
following procedure for each card.
Basic Installation Instructions
Use the procedure below that corresponds to the version of Windows you are using:
•
Windows Vista
•
Windows XP, 2000, 98SE 2nd edition, or Me
•
Windows NT 4.0
Note:
1000BASE-T signaling requires four twisted pairs of Category 5 balanced cabling,
as specified in ISO/IEC 11801:1995 and ANSI/EIA/TIA-568-A (1995) and tested
using procedures defined in TIA/EIA TSB95.