Oki ML8480FB ML8480FB User's Guide - Page 49

PE Adj. (Front) [Paper End Adjust (Front Feed)], PE Pos. [Paper End Position], Pitch, Power Save Time

Get Oki ML8480FB PDF manuals and user guides View all Oki ML8480FB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

PE Adj. (Front) [Paper End Adjust (Front Feed)] For fine tuning the location of the last line of printing (Paper End) when using continuous forms (front feed). Settable from -15 to +15 in increments of 1/120 inch. The default is 0. Negative values allow printing further down on the form: • Paper End moves down • paper moves up. Positive values stop the printing further up on the form: • Paper End moves up • paper moves down PE Pos. [Paper End Position] This sets when the the printer will move to the next continuous form, based on the distance between the center of the characters on the last line of the form and the bottom of the form. Available settings: 3.18 mm (1/8") or 6.35 mm (1/4") [the default]. Pitch Choose the character width, in characters per inch (cpi): 10 [the default], 12, 15, 17.1, or 20 cpi. Power Save Time Sets the time the printer waits before entering the Power Save Mode when Power Saving is set to Enable [the default]: 5 min, 10 min [the default], 15 min, 30 min, or 60 min. Power Saving Sets whether or not the printer enters the energy-saving Power Save Mode after the interval specified under Power Save Time. The default is Enable. Print Dir. Cmd. The default is Valid: the printer will recognize a command for unidirectional printing. Change to Invalid if you do not wish the printer to recognize uni-directional printing commands. Microline 8480FB User's Guide • 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Microline 8480FB User°s Guide
± 49
PE Adj. (Front) [Paper End Adjust (Front Feed)]
For fine tuning the location of the last line of printing (Paper End)
when using continuous forms (front feed). Settable from -15 to
+15 in increments of 1/120 inch. The default is 0.
Negative values allow printing further down on the form:
±
Paper End moves down
±
paper moves up.
Positive values stop the printing further up on the form:
±
Paper End moves up
±
paper moves down
PE Pos. [Paper End Position]
This sets when the the printer will move to the next continuous
form, based on the distance between the center of the characters
on the last line of the form and the bottom of the form. Available
settings:
3.18 mm (1/8") or 6.35 mm (1/4") [the default].
Pitch
Choose the character width, in characters per inch (cpi): 10 [the
default], 12, 15, 17.1, or 20 cpi.
Power Save Time
Sets the time the printer waits before entering the Power Save
Mode when Power Saving is set to Enable [the default]: 5 min, 10
min [the default], 15 min, 30 min, or 60 min.
Power Saving
Sets whether or not the printer enters the energy-saving Power
Save Mode after the interval specified under Power Save Time. The
default is Enable.
Print Dir. Cmd.
The default is Valid: the printer will recognize a command for
unidirectional printing. Change to Invalid if you do not wish the
printer to recognize uni-directional printing commands.