Onkyo TX-NR5008 Owner Manual - Page 50

Digital Audio Input If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign "OPT 1" to the "TV/CD" input selector. Here are the default assignments. Input selector BD/DVD VCR/DVR CBL/SAT GAME PC AUX TAPE TUNER TV/CD PHONO PORT Default assignment COAX 1 COAX 2 COAX 3 OPT 1 ----FRONT (Fixed Fixed) OPT 2 --------- ■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TAPE, TV/CD, PHONO, PORT ` COAX 1, COAX 2, COAX 3, OPT 1, OPT 2, OPT 3 (TX-NR5008): Select a corresponding digital audio input that the component has been connected Select if the component is connected to an analog audio input. • "AUX" is used only for input from the front panel. Note • When an HDMI IN is assigned to an input selector in "HDMI Input" (➔ 48), the same HDMI IN will be set as a priority in this assignment. In this case, if you want to use the coaxial or optical audio input, make the selection in the "Audio Selector" in the Home menu (➔ 68). • Available sampling rate for PCM signals from a digital input (optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit. • "TUNER" selector cannot be assigned and is fixed at the option. • If you connect a component (such as UP-A1 Dock that seated iPod) to the UNIVERSAL PORT jack, you cannot assign any input to "PORT" selector. Analog Audio Input If you connect a component to the AV receiver's analog multichannel input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/ DVD player to the MULTI CH input, you must assign it to the "BD/DVD" input selector. ■ Multich ` BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX, TAPE, TV/CD, PHONO You can assign the multichannel input to the input selectors If you don't want to assign the multichannel input, set to En 50 Note • To listen to the component connected to the multichannel input, make the selection in the "Audio Selector" in the Home menu (➔ 68). ■ Subwoofer Input Sensitivity ` 0dB to 15dB in 5 dB step. Some DVD players output the LFE channel from their analog subwoofer output at 15 dB higher than normal. With this setting, you can change the AV receiver's subwoofer sensitivity to match your DVD player. Note • This setting only affects signals connected to the AV receiver's multichannel input SUBWOOFER jack. • If you find that your subwoofer is too loud, try the 10 dB or 15 dB setting. Speaker Setup Main menu Speaker Setup Some of the settings in this section are set automatically by Audyssey MultEQ® XT32 Room Correction and Speaker Setup (➔ 32). For Speakers B, you need to change the settings manually. Here you can check the settings made by Audyssey MultEQ XT32 Room Correction and Speaker Setup, or set them manually, which is useful if you change one of the connected speakers after using Audyssey MultEQ XT32 Room Correction and Speaker Setup. Press RECEIVER and use SP LAYOUT on the remote controller to select Speakers A or Speakers B. Note • These settings are disabled when: - a pair of headphones is connected, or - the "Audio TV Out" setting is set to "On" (➔ 64) and an input selector other than HDMI is selected. Speaker Settings If you change these settings, you must run Audyssey MultEQ XT32 Room Correction and Speaker Setup again (➔ 32). If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms. To use bi-amping or bridging, you must change the "Speakers Type(Front A)" or "Speakers Type(Front B)" setting (➔ 51). For details on speaker wire connection, see "Connecting the AV Receiver" (➔ 17 to 19). Note • When bridging is used, the AV receiver is able to drive up to 7.2 speakers in the main room. • When bi-amping is used, the AV receiver is able to drive up to 7.2 speakers in the main room. • Before you change these settings, turn down the volume.