Onkyo TX-NR5008 Owner Manual - Page 69

Setting the Incoming Digital Signal Fixed, ENTER, Fixed Mode - reset

Get Onkyo TX-NR5008 PDF manuals and user guides View all Onkyo TX-NR5008 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Setting the Incoming Digital Signal (Fixed Mode) By pressing ENTER while selecting "HDMI", "COAX", "OPT" in the "Audio Selector", you can specify the input signal in the Fixed Mode. Pressing ENTER again allows you to return to the "Audio Selector" setting. Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS. • If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM. • If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS. ■ Fixed Mode ` Auto: The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead. ` PCM: Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and noise may also be produced. ` DTS: Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound. Note • The setting is stored individually for each input selector. • The setting will be reset to "Auto" when you change the setting in the "Audio Selector" (➔ 68). En 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
69
En
Setting the Incoming Digital Signal (Fixed
Mode)
By pressing
ENTER
while selecting “
HDMI
”, “
COAX
”,
“
OPT
” in the “
Audio Selector
”, you can specify the input
signal in the Fixed Mode. Pressing
ENTER
again allows
you to return to the “
Audio Selector
” setting.
Normally, the AV receiver detects the signal format auto-
matically. However, if you experience either of the follow-
ing issues when playing PCM or DTS material, you can
manually set the signal format to PCM or DTS.
• If the beginnings of tracks from a PCM source are cut
off, try setting the format to PCM.
• If noise is produced when fast forwarding or reversing a
DTS CD, try setting the format to DTS.
■
Fixed Mode
Auto
:
The format is detected automatically. If no digital
input signal is present, the corresponding analog
input is used instead.
PCM
:
Only 2-channel PCM format input signals will be
heard. If the input signal is not PCM, the
PCM
indi-
cator will flash and noise may also be produced.
DTS
:
Only DTS (but not DTS-HD) format input signals
will be heard. If the input signal is not DTS, the
DTS
indicator will flash and there will be no sound.
Note
•
The setting is stored individually for each input selector.
•
The setting will be reset to “
Auto
” when you change the setting
in the “
Audio Selector
” (
➔
68
).