Optoma GT5600 EH340UST User Manual - Page 19

USING THE PROJECTOR, Powering on / off the projector

Get Optoma GT5600 PDF manuals and user guides View all Optoma GT5600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

USING THE PROJECTOR Powering on / off the projector Power Switch or Freeze L R Power Switch Freeze L R Enter Enter Page- Laser Page+ Keystone -+ Volume -+ 1 4 HDMI 7 User1 Source 2 Menu 5 VGA 8 User2 0 3 3D 6 Video 9 User3 Resync Page- Laser Page+ Powering 1. on Securely connect the power lead and signal/source cable. Keystone Volume W-hen co+nnecte-d, the O+n/Standby LED will turn red. 1 2 3 2. Turn on the projector by pressing the " " either on the projector keypMadenour the 3reDmote control. 3. A start blue. up screen will display in approximately 10 seconds and 4the On/S5tandby L6 ED will be flashing HDMI VGA Video Note: The first time the projector is turned on, you will be prompted to selec7 t the pre8ferred la9nguage, projection orientation, and other settings. User1 User2 User3 Powering off 0 1. Turn off the projector by pressing the " " either on the projecStoourrckeeypad or theRerseynmcote control. 2. The following message will be displayed: Power Off Power Off? Press power key again. 3. Press the " " again to confirm, otherwise the message will disappear after 10 seconds. When you press the " " button for the second time, the projector will shut down. 4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/ Standby LED will flash blue. When the On/Standby LED turns solid red, this indicates the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and the projector has entered standby mode. When the projector is in standby mode, simply press the " " button again to turn on the projector. 5. Disconnect the power lead from the electrical outlet and the projector. Note: It is not recommended that the projector is turned on immediately, right after a power off procedure. English 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
English
19
USING THE PROJECTOR
Powering on / off the projector
Freeze
Power
Switch
L
R
Keystone
Volume
Page
-
-
+
-
+
1
2
Menu
3
3D
4
HDMI
5
VGA
6
Video
7
User1
8
User2
9
User3
Source
0
Resync
Page+
Laser
Enter
Freeze
Power
Swit
or
Powering on
1.
Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will
turn red.
2.
Turn on the projector by pressing the "
" either on the projector keypad or the remote control.
3.
A start up screen will display in approximately 10 seconds and the On/Standby LED will be flashing
blue.
Note°
The first time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering off
1.
Turn off the projector by pressing the "
" either on the projector keypad or the remote control.
2.
The following message will be displayed:
Power Off
Power Off?
Press power key again.
3.
Press the "
" again to confirm, otherwise the message will disappear after 10 seconds. When you
press the "
" button for the second time, the projector will shut down.
4.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/
Standby LED will flash blue. When the On/Standby LED turns solid red, this indicates the projector has
entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle
has finished and the projector has entered standby mode. When the projector is in standby mode,
simply press the "
" button again to turn on the projector.
5.
Disconnect the power lead from the electrical outlet and the projector.
Note°
It is not recommended that the projector is turned on immediately, right after a power off procedure.