Panasonic KV-S3105C Operating Instructions - Page 16

Others menu

Get Panasonic KV-S3105C PDF manuals and user guides View all Panasonic KV-S3105C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Display Panel Instructions Others menu No. Item LCD display Contents Page 01 Checking the version Version Displays the firmware version of the mechanical control, interface control or post-imprinter. If an optional imprinter is not installed, the imprinter 25 version will not be displayed. 02 Setting the buzzer Buzzer Selects whether the buzzer is turned on or off. If selection is in the "ON" position: When pressing a key, one short beep will be heard. When there is an error, 5 short beeps will be heard. 25 When scanning is completed correctly, one long beep will be heard. 03 Setting the SCSI ID SCSI ID Sets the SCSI ID number. 25 04 Setting the wide SCSI Wide SCSI • Sets "Enable" or "Disable". • Set "Disable" when the connector of the PC is 25 narrow. 05 Setting the transfer rate • Changes the maximum value of the synchronous transfer rate of the SCSI interface. Transfer Rate • Lower the synchronous transfer rate to 10 Mbytes/ 25 sec. if the computer has failed to recognize the scanner or the scanner fails to operate properly. Checking the roller cleaning warning 06 Clearing the roller cleaning warning Clean Roller Warning The alarm tells you it is time to check the roller. If it is near 100%, clean the roller. See "Cleaning the 25 Unit" on page 37. Clean Roller Warning Clear Clear the "Clean Roller Warning ≤≤%" display. 25 Checking the roller Replace modules replacement Roller warning 07 Warning The alarm tells you the roller needs to be changed. If it is near 100%, replace the paper feed roller module and retard roller module. See "Replacing 26 Consumables" on page 43. Clearing the roller modules replacement warning Replace Roller Warning Clear Clear the "Replace Roll. Warning ≤≤%" display. 26 08 Setting the product ID Product ID Selects the product ID. The product ID setting depends on the host computer scanner application you are using. Allows scanner to emulate other 26 Panasonic scanners. 09 Setting the sleep mode Sleep Mode Sets the time until sleep mode turns ON. 26 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
Display Panel Instructions
16
Others menu
No.
Item
LCD display
Contents
Page
01
Checking the version
Version
Displays the firmware version of the mechanical
control, interface control or post-imprinter. If an
optional imprinter is not installed, the imprinter
version will not be displayed.
25
02
Setting the buzzer
Buzzer
Selects whether the buzzer is turned on or off. If
selection is in the “ON” position:
When pressing a key, one short beep will be heard.
When there is an error, 5 short beeps will be heard.
When scanning is completed correctly, one long
beep will be heard.
25
03
Setting the SCSI ID
SCSI ID
Sets the SCSI ID number.
25
04
Setting the wide
SCSI
Wide SCSI
• Sets “Enable” or “Disable”.
• Set “Disable” when the connector of the PC is
narrow.
25
05
Setting the transfer
rate
Transfer Rate
• Changes the maximum value of the synchronous
transfer rate of the SCSI interface.
• Lower the synchronous transfer rate to 10 Mbytes/
sec. if the computer has failed to recognize the
scanner or the scanner fails to operate properly.
25
06
Checking the roller
cleaning warning
Clean Roller
Warning
The alarm tells you it is time to check the roller. If it
is near 100%, clean the roller. See “Cleaning the
Unit” on
page 37.
25
Clearing the roller
cleaning warning
Clean Roller
Warning Clear
Clear the “Clean Roller Warning
≤≤
%” display.
25
07
Checking the roller
modules replacement
warning
Replace
Roller
Warning
The alarm tells you the roller needs to be changed.
If it is near 100%, replace the paper feed roller
module and retard roller module. See “Replacing
Consumables” on
page 43.
26
Clearing the roller
modules replacement
warning
Replace Roller
Warning Clear
Clear the “Replace Roll. Warning
≤≤
%” display.
26
08
Setting the product
ID
Product ID
Selects the product ID. The product ID setting
depends on the host computer scanner application
you are using. Allows scanner to emulate other
Panasonic scanners.
26
09
Setting the sleep
mode
Sleep Mode
Sets the time until sleep mode turns ON.
26