Panasonic PT AX100U Hd Home Cinema Projector - Page 35

Installation, Sleep, Altitude, Lamp Power, Lamp Runtime, Test Pattern, Settings - - replacement lamp

Get Panasonic PT AX100U - LCD Projector - HD 720p PDF manuals and user guides
UPC - 791871111383
View all Panasonic PT AX100U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

OPTION Menu INSTALLATION LAMP RUNTIME When installing the projector, select the projection method according to the projector position. Press I H to cycle through the options. See "Projection method" on page 15. FRONT/DESK FRONT/CEILING REAR/DESK REAR/CEILING Setting on a desk/floor and projecting from front Mounting in the ceiling and projecting from front Setting on a desk/floor and projecting from rear Mounting in the ceiling and projecting from rear SLEEP You can check how long time has been the lamp used. NOTE: LAMP RUNTIME is a relevant matter for lamp replacement timing. See "Care and Replacement" on page 37. TEST PATTERN You can use the 2 different of test pattern to adjust the focus of the image. The PICTURE MODE is switched to DYNAMIC temporarily, and return to the last used setting when return to projection. 1. Press ENTER to display test pattern 1 and adjust the focus with the Focus ring. You can select the required duration of time and set the off timer to turn off the POWER of the projector automatically. 3 minutes before turn-off, the countdown of minutes will be displayed in the lower right corner. Press I H to cycle through the options. See "Switching off the projector automatically" on page 23. ALTITUDE 2. Press ENTER to display test pattern 2 and adjust the focus with the Focus ring again. If you use the projector at high elevations, set the fan speed to HIGH. Press I H to select HIGH or LOW. NOTE: At 1 400 m (4593 ft) above sea level, the setting must be HIGH. LAMP POWER You can adjust the power of the lamp to save on electricity, prolong the lamp life and reduce the noise. Options NORMAL ECO - MODE Function When higher luminance is required such as movies When lower luminance is sufficient such as in a small room 3. Press MENU or RETURN to return to the previous menu, or press repeatedly to return to the screen. NOTE: While a test pattern is displayed, the PICTURE MODE is changed temporarily to DYNAMIC. When the projector and/or the screen is tilted, adjust the focus at the center of the image. The upper and lower edge might be out of focus. When the image is distorted in keystone, adjust the KEYSTONE in POSITION menu. NOTE: When no input signal is detected, the function is disabled. Settings ENGLISH - 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
OPTION Menu
E
NGLISH
- 35
Settings
When installing the projector, select the projection
method according to the projector position. Press
IH
to cycle through the options. See “Projection method”
on page 15.
You can select the required duration of time and set the
off timer to turn off the
POWER
of the projector
automatically. 3 minutes before turn-off, the countdown
of minutes will be displayed in the lower right corner.
Press
IH
to cycle through the options. See “Switching
off the projector automatically” on page 23.
If you use the projector at high elevations, set the fan
speed to
HIGH
. Press
IH
to select
HIGH
or
LOW
.
You can adjust the power of the lamp to save on
electricity, prolong the lamp life and reduce the noise.
You can check how long time has been the lamp used.
You can use the 2 different of test pattern to adjust the
focus of the image. The
PICTURE MODE
is switched to
DYNAMIC
temporarily, and return to the last used
setting when return to projection.
1.
Press
ENTER
to display test pattern 1 and adjust
the focus with the
Focus ring
.
2.
Press
ENTER
to display test pattern 2 and adjust
the focus with the
Focus ring
again.
3.
Press
MENU
or
RETURN
to return to the previous
menu, or press repeatedly to return to the screen.
INSTALLATION
FRONT/DESK
Setting on a desk/floor and
projecting from front
FRONT/CEILING
Mounting in the ceiling and
projecting from front
REAR/DESK
Setting on a desk/floor and
projecting from rear
REAR/CEILING
Mounting in the ceiling and
projecting from rear
SLEEP
ALTITUDE
NOTE:
At 1 400 m (4593 ft) above sea level, the setting
must be
HIGH
.
LAMP POWER
Options
Function
NORMAL
When higher luminance is
required such as movies
ECO - MODE
When lower luminance is
sufficient such as in a small room
NOTE:
When no input signal is detected, the function is
disabled.
LAMP RUNTIME
NOTE:
LAMP RUNTIME
is a relevant matter for lamp
replacement timing. See “Care and Replacement”
on page 37.
TEST PATTERN
NOTE:
While a test pattern is displayed, the
PICTURE
MODE
is changed temporarily to
DYNAMIC
.
When the projector and/or the screen is tilted,
adjust the focus at the center of the image. The
upper and lower edge might be out of focus.
When the image is distorted in keystone, adjust
the
KEYSTONE
in
POSITION
menu.