Pfaff creative sensation Owner's Manual - Page 142

Common, Embroidery stitch-out, pop-ups

Get Pfaff creative sensation PDF manuals and user guides View all Pfaff creative sensation manuals
Add to My Manuals
Save this manual to your list of manuals

Page 142 highlights

Embroidery mode - stitch-out Common Embroidery stitch-out pop-ups Embroidery unit calibration When the embroidery unit is attached, a pop-up asks you to slide off the hoop and clear the machine area for calibrating the embroidery arm. You will also be reminded to disengage the IDT™ system and attach the Dynamic spring foot 6D for embroidery. Note: It is very important to remove the hoop, otherwise the hoop or the embroidery unit may be damaged while calibrating. Attach correct hoop If the size of the hoop attached to the machine does not match the size displayed on screen, the machine will not embroider. You must change the hoop to the displayed size or change the hoop setting to the hoop size attached. To change hoop settings, re-enter Embroidery edit and go to select hoop. Bobbin empty - move to bobbin position? When the bobbin is almost empty, the machine stops automatically and a pop-up appears on the screen. Touch cancel to remain at the current stitch position. Touch OK to move the hoop to bobbin position. The hoop position tab opens. Replace the empty bobbin with a full one. Touch Current position and pull back excess needle thread. Move a few stitches backwards using the current stitch icons (4). Press start/stop or press your foot control to continue embroidering. 4 Note: It is possible to embroider until the thread has completely run out. Press the start/stop button to continue embroidering without closing the bobbin empty pop-up. 9:12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
9:12
4
Embroidery mode - stitch-out
Common
Embroidery stitch-out
pop-ups
Embroidery unit calibration
When the embroidery unit is attached, a pop-up
asks you to slide off the hoop and clear the machine
area for calibrating the embroidery arm. You will
also be reminded to disengage the
IDT™
system and
attach the Dynamic spring foot 6D for embroidery.
Note: It is very important to remove the hoop, otherwise
the hoop or the embroidery unit may be damaged while
calibrating.
Attach correct hoop
If the size of the hoop attached to the machine does
not match the size displayed on screen, the machine
will not embroider. You must change the hoop to
the displayed size or change the hoop setting to the
hoop size attached.
To change hoop settings, re-enter Embroidery edit
and go to select hoop.
Bobbin empty - move to bobbin position?
When the bobbin is almost empty, the machine
stops automatically and a pop-up appears on the
screen.
Touch cancel to remain at the current stitch position.
Touch OK to move the hoop to bobbin position.
The hoop position tab opens. Replace the empty
bobbin with a full one. Touch Current position and
pull back excess needle thread. Move a few stitches
backwards using the current stitch icons (4). Press
start/stop or press your foot control to continue
embroidering.
Note: It is possible to embroider until the thread has
completely run out. Press the start/stop button to
continue embroidering without closing the bobbin empty
pop-up.