Samsung CLP-775 User Manual (user Manual) (ver.1.01) (English) - Page 86

Necessary Precautions to take when installing accessories

Get Samsung CLP-775 PDF manuals and user guides View all Samsung CLP-775 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

belt. After the life span of the paper transfer belt is complete, you have to replace it. • The transfer belt-related message appears on the display, telling it's time for a replacement. The life span of the paper transfer belt may be affected by operating environment, printing interval, media type, and media size. 1. Using the handle, completely open the front cover. 5. Holding the handle on the new paper transfer belt, align it with the slots on the inside of the front cover. 6. Lower the paper transfer belt until it is parallel with the front cover and firmly seated. • Do not touch the green surface, the OPC drum or the front of the print cartridge, with your hands or any other material. Use the handle on each cartridge in order to avoid touching this area. • Be careful not to scratch the surface of the paper transfer belt. • If you leave the front cover open for more than a few minutes, the OPC drum can be exposed to light. This will cause damage to the OPC drum. Close the front cover should the installation need to be halted for any reason. 2. Press the green release handle to release the paper transfer belt. Holding the handle on the paper transfer belt, lift it out of the machine. 3. Remove a new paper transfer belt from its bag. 4. Remove the paper covering the paper transfer belt. • Do not use sharp objects, such as a knife or scissors, to open the paper transfer belt package. You could damage the surface of the paper transfer belt. • Be careful not to scratch the surface of the paper transfer belt. 7. Close the front cover to resume printing. If the front cover is not completely closed, the machine will not operate. Necessary Precautions to take when installing accessories • Disconnect the power cord. Never remove the control board cover while the power is turned on. To avoid the possibility of an electrical shock, always disconnect the power cord when installing or removing ANY internal or external accessories. • Discharge static electricity. The control board and internal accessories (network interface card or memory module) are sensitive to static electricity. Before installing or removing any internal accessories, discharge static electricity from your body by touching something metal, such as the metal back plate on any device plugged into a grounded power source. If you walk around before finishing the installation, repeat this procedure to discharge any static electricity again. • Activating the added accessories in the PS driver properties. After installing an accessory such as an optional tray, PS driver users must do the additional setting. Go to the PS printer properties and set the added accessory activated. Supplies and accessories_ 86

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
Supplies and accessories
_ 86
belt.
After the life span of the paper transfer belt is complete, you have to replace
it.
•
The transfer belt-related message appears on the display, telling it's
time for a replacement.
The life span of the paper transfer belt may be affected by operating
environment, printing interval, media type, and media size.
1.
Using the handle, completely open the front cover.
•
Do not touch the green surface, the OPC drum or the front of
the print cartridge, with your hands or any other material. Use
the handle on each cartridge in order to avoid touching this
area.
•
Be careful not to scratch the surface of the paper transfer belt.
•
If you leave the front cover open for more than a few minutes,
the OPC drum can be exposed to light. This will cause damage
to the OPC drum. Close the front cover should the installation
need to be halted for any reason.
2.
Press the green release handle to release the paper transfer belt.
Holding the handle on the paper transfer belt, lift it out of the machine.
3.
Remove a new paper transfer belt from its bag.
4.
Remove the paper covering the paper transfer belt.
•
Do not use sharp objects, such as a knife or scissors, to open
the paper transfer belt package. You could damage the surface
of the paper transfer belt.
•
Be careful not to scratch the surface of the paper transfer belt.
5.
Holding the handle on the new paper transfer belt, align it with the slots
on the inside of the front cover.
6.
Lower the paper transfer belt until it is parallel with the front cover and
firmly seated.
7.
Close the front cover to resume printing.
If the front cover is not completely closed, the machine will not
operate.
Necessary Precautions to take when installing
accessories
•
Disconnect the power cord.
Never remove the control board cover while the power is turned on.
To avoid the possibility of an electrical shock, always disconnect the
power cord when installing or removing ANY internal or external
accessories.
•
Discharge static electricity.
The control board and internal accessories (network interface card or
memory module) are sensitive to static electricity. Before installing or
removing any internal accessories, discharge static electricity from your
body by touching something metal, such as the metal back plate on any
device plugged into a grounded power source. If you walk around before
finishing the installation, repeat this procedure to discharge any static
electricity again.
•
Activating the added accessories in the PS driver properties.
After installing an accessory such as an optional tray, PS driver users
must do the additional setting. Go to the PS printer properties and set
the added accessory activated.