Samsung DVD-VR300 User Manual (user Manual) (ver.1.0) (English) - Page 21

Connecting the Power Cord, Preparing the Remote Control

Get Samsung DVD-VR300 PDF manuals and user guides View all Samsung DVD-VR300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Step 6 : Connecting the Power Cord Step 7 : Preparing the Remote Control After all connections are complete, plug the power cord in the wall outlet. "AUTO" in the front panel display flickers. This means that the current time is being set automatically (Auto Program) through the antenna under connection. The setup may take several minutes. When it normally operates, the current time is automatically set and displayed in the front panel display. If "- - - -" appears, however, it means that auto time setting has failed. In that case, set the current time through the manual clock set, as shown in pages 25~26. Install Batteries in the Remote Control • Open the battery cover on the back of the remote. • Insert two AAA batteries. Make sure that the polarities (+ and -) are aligned correctly. • Replace the battery cover. If the remote does not operate properly: • Check the polarity + - of the batteries (Dry-Cell) • Check if the batteries are drained. • Check if the remote sensor is blocked by obstacles. • Check if there is any fluorescent lighting nearby. Dispose of batteries according to local environmental regulations. Do not put them in the household trash. Connections English - 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
C
onnections
English
-
21
After all connections are complete, plug the power cord
in the wall outlet.
“AUTO” in the front panel display flickers. This means that
the current time is being set automatically (Auto Program)
through the antenna under connection. The setup may take
several minutes.
When it normally operates, the current time is automatically
set and displayed in the front panel display.
If “- - - -“ appears, however, it means that auto time setting
has failed.
In that case, set the current time through the manual clock
set, as shown in pages 25~26.
Step 6 : Connecting
the Power Cord
Dispose of batteries according to local environmental regula-
tions. Do not put them in the household trash.
Install Batteries in the Remote Control
•
Open the battery cover on the back of the remote.
• Insert two AAA batteries. Make sure that the polarities
(+ and -) are aligned correctly.
•
Replace the battery cover.
If the remote does not operate properly:
•
Check the polarity + - of the batteries (Dry-Cell)
•
Check if the batteries are drained.
•
Check if the remote sensor is blocked by obstacles.
•
Check if there is any fluorescent lighting nearby.
Step 7 : Preparing the
Remote Control