Sanyo PDG-DET100L Instruction Manual, PDG-DET100L POA-MD13NET2 - Page 22

Password setting [Display], Select

Get Sanyo PDG-DET100L - SXGA+ DLP Projector PDF manuals and user guides
UPC - 086483074684
View all Sanyo PDG-DET100L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

For the Projector which provides the Network sub menu in the Setting main menu Chapter 2 Installation Password setting [Display] A password can be set to restrict access to the setting pages of the projector using the web browser. The default password is set "0000" as no password. Password 0000 SET CANCEL 1 Use the projector's menu and select the Setting icon on the menu. 2 Select the Display sub icon from the submenu, and then press the SELECT button once. Check that the mode is "On". 3 Then press the SELECT button once again. *The setting window appears. The numbers on the display indicates the current password. 4 Enter your desired number by using the point buttons on the projector or remote control, and then select SET and press the SELECT button. *The password setting window disappears and the Network Board begins restarting. It takes about 40 seconds. Do not turn off the mains switch during this period. ✐ Password setting must be done when you connect the projector to the network. This setting is carried out through the projector's menu and also it can be set through the network using the web browser. For further information please refer to item "Initial Setting/Password setting" (☞ p.30). ✐ Valid characters for password are only 4 digits numeric numbers 0 to 9. The number "0000" means no password set. ✐ This password is not to restrict the use of the projector. This password is to set the security against the use of the projector through the network. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
22
Chapter 2 Installation
✐
Password setting must be done when you connect the projector to the network. This setting
is carried out through the projector’s menu and also it can be set through the network using
the web browser. For further information please refer to item “Initial Setting/Password set-
ting” (
☞
p.30).
✐
Valid characters for password are only 4 digits numeric numbers 0 to 9. The number “0000”
means no password set.
✐
This password is not to restrict the use of the projector. This password is to set the security
against the use of the projector through the network.
Password setting [Display]
A password can be set to restrict access to the setting pages of the projector using
the web browser.
The default password is set “0000” as no password.
1
Use the projector’s menu and select the
Setting
icon on the menu.
2
Select the
Display
sub icon from the submenu, and then press the
SELECT
button
once. Check that the mode is “On”.
3
Then press the
SELECT
button once again.
*The setting window appears. The numbers on the display indicates the current password.
4
Enter your desired number by using the point buttons on the projector or remote
control, and then select
SET
and press the
SELECT
button.
*The password setting window disappears and the Network Board begins restarting. It takes
about 40 seconds. Do not turn off the mains switch during this period.
Password
0
0
0
0
SET
CANCEL
For the Projector which provides the Network sub menu in the Setting main menu