Sharp AR-M355U AR-M355 AR-M455 Operation Manual Suite - Page 295

CHECKING THE SIZE OF A LOADED ORIGINAL When a standard-size* original is placed, the original size is automatically detected (automatic original detection function) and displayed in the top half of the [ORIGINAL] key. Check the key to make sure that the original size has been correctly detected. :[AUTO] appears when the automatic original detection function is operating. :Displays the original size. If a non-standard size original is placed or if you wish to change the scanning size, follow the steps below to manually set the original scanning size. STANDARD RESOLUTION AUTO 81/2X11 ORIGINAL NOTE * Standard sizes that can be detected are as follows: 5-1/2"x8-1/2", 8-1/2"x11", 8-1/2"x11"R, 8-1/2"x14", 11"x17", A5, B5, B5R, A4, A4R, B4, A3. If a non-standard size original is loaded (including special sizes), the closest standard size may be displayed, or the original size may not appear at all. MANUALLY SETTING THE SCANNING SIZE If you load an original that is not a standard size (such as an AB size), or if the size is not detected correctly, you must touch the [ORIGINAL] key and set the original size manually. Perform the following steps after loading the document in the automatic document feeder or on the document glass. 1 Touch the [ORIGINAL] key. If you placed a non-standard size original on the document holder or on the STANDARD RESOLUTION AUTO 81/2X11 ORIGINAL If the address book screen appears, touch the [CONDITION SETTINGS] key to display the condition settings screen (page 1-5). document glass, touch the [SIZE INPUT] tab and then enter the width (X) and length (Y) of the original with the keys. X (width) is initially selected. X OK Enter X and then touch the Y AY ( ) key to enter Y. A width of X 17 (2 1/2 17) inch 2-1/2 to 17 inch (64 to 432 mm) 2 Touch the key under [SCAN SIZE]. Y 11 (2 1/2 11 5/8) inch can be entered in X, and a length of 2-1/2 to 11-5/8 inch (64 STANDARD SIZE SIZE INPUT to 297 mm) can be entered in Y. SPEAKER If you frequently send documents that are the same non- SCAN SIZE AUTO 81/2X11 SEND SIZE 100% AUTO standard size, you can store the dimensions as explained in "STORING, DELETING, AND USING ORIGINAL SIZES" on the following page. This will allow you to omit 2-SIDED BOOKLET 2-SIDED TABLET entry of X and Y each time you send that size of document. 3 Touch the desired original size key. 4 Touch the outer [OK] key. Touch the [OK] key to return to the screen of step 2. SPEAKER RESEND 5 X8 1/2 1/2 81/2 X13 OK 5 X8 1/2 1/2 R 81/2X14 AB INCH 81/2X11 11X17 81/2 X11R LONG SIZE STANDARD SIZE SIZE INPUT [AUTO] is no longer highlighted. [MANUAL] and the original size key you touched are highlighted. If you placed a long original, touch the LONG SIZE key. 5 Touch the outer [OK] key. SPEAKER SEND SIZE AUTO RESEND OK If you wish to select an AB size, touch the [AB/INCH] key and then touch the desired original size key. 81/2X11 AUTO MANUAL STOM ZE SPEAKER RESEND A5 A4 OK A5R A4R AB INCH B5 B4 B5R A3 LONG SIZE STANDARD SIZE SIZE INPUT [AB] is highlighted and AB size keys are displayed. To return to the inch palette, touch the [AB/INCH] key once again. -SIDED 6 The selected size appears in the top half of the [ORIGINAL] key. STANDARD RESOLUTION A4 ORIGINAL 1-8