Sharp AR-M355U AR-M355 AR-M455 Operation Manual Suite - Page 351
Storing A Program, Editing And Deleting Programs, Touch The [program Name] Key.
View all Sharp AR-M355U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 351 highlights
STORING, EDITING, AND DELETING AUTO DIAL KEYS AND PROGRAMS STORING A PROGRAM You can store a destination fax number, speed dialing, polling, erase, dual page scan, 2in1, card shot, and resolution and exposure settings in a program. This enables you to call up the program and perform the transmission by means of a simplified operation. (See "USING A PROGRAM" on page 3-17.) NOTE A timer setting (page 3-6) cannot be included in a program. When storing a program for an F-Code operation, one touch keys for destinations must include sub-addresses. To store a program key, follow steps 1 through 3 on page 6-2, touch the [PROGRAM] key in step 4, and then follow these steps. 1 Touch the [PROGRAM NAME] key. PROGRAM The "No." that No.1 automatically appears is PROGRAM NAME SETTINGS ADDRESS the lowest number from 1 to 8 that has not yet been programmed. When the RESOLUTION [PROGRAM NAME] key is touched, the letter-entry screen appears. Enter up to 18 characters for the name. Refer to chapter 7 of "Operation manual (for general information and copier operation)" for the procedure for entering letters. 2 Touch the [SETTINGS] key. No.1 PROGRAM NAME PROGRAM FOR SHARP SETTINGS ADDRESS RESOLUTION For the detailed procedures for each of the settings, refer to the explanations of those features on the following pages. [RESOLUTION](page 1-10) [EXPOSURE](page 1-11) [SPEED DIAL](page 2-4) [ADDRESS BOOK] (page 3-3) [SPECIAL MODES] G ERASE (page 3-4) G DUAL PAGE SCAN (page 3-5) G 2in1 (page 3-7) G CARD SHOT (page 3-8) G POLLING (page 3-13) NOTE Up to 500 (maximum of 300 on the AR-M355U/AR-M455U) destinations can be stored in a program. However, you cannot directly enter fax numbers with the numeric keys. A destination must be programmed in an auto dial key (onetouch key or group key) before it can be stored in a program. 4 Touch the [OK] key. 5 Your settings are displayed. Make sure they are correct. PROGRAM No.1 REGISTRATION NEXT EXIT SPECIAL MODES 3 Touch the keys for the settings you wish to store. PROGRAM NAME SHARP PROGRAM SETTINGS ADDRESS 2 ADDRESSES RESOLUTION FINE SPECIAL MODES DUAL PAGE SCAN EXPOSURE AUTO ENTER PROGRAM YOU REQUIRE. AUTO EXPOSURE STANDARD RESOLUTION CANCEL OK FAX MODE SWITCH ADDRESS BOOK ADDRESS REVIEW SPECIAL MODES 6 When you are finished, touch the [EXIT] key. If you wish to store another program, touch the [NEXT] key. Touching the [EXIT] key returns you to the screen of step 4 on page 6-2. Touching the [NEXT] key returns you to the screen of step 1. EDITING AND DELETING PROGRAMS To edit or delete a previously stored program, follow steps 1 to 3 on page 6-2, touch the [AMEND/DELETE] key in the screen of step 4, and then follow these steps. 1 Touch the [PROGRAM] key. 2 Touch the program you wish to edit or delete. EXIT 1/2 PROGRAM DIRECT ADDRESS / AMEND/DELETE SELECT ADDRESS TO AMEND/DELETE. PROGRAM PROGRAM FOR SHARP EMAIL NEWS GROUP EXIT ADDRESS BOOK ABYS FAX FORMAT A 6-8 G When you touch the program name, the edit/delete screen for the selected program appears. G Touching the [ADDRESS BOOK] key returns you to the screen of step 1. 3 To edit the program, follow the same procedure as for storing the program. To delete the program, touch the [DELETE] key and then touch the [YES] key in the confirmation screen that appears.