Sharp AR-M355U AR-M355 AR-M455 Operation Manual Suite - Page 312
Using Broadcast Transmission
View all Sharp AR-M355U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 312 highlights
SENDING THE SAME DOCUMENT TO MULTIPLE DESTINATIONS IN A SINGLE OPERATION (BROADCAST TRANSMISSION) USING BROADCAST TRANSMISSION 1 Perform steps 1 through 6 of "BASIC PROCEDURE FOR SENDING FAXES" (page 2-2). 2 Dial the fax number of the first destination or touch an auto-dial key (one-touch key, group key or speed dial key). (Refer to page 2-4.) If the condition settings CORPO. TPS SHARP GROUP screen appears, touch the SPE [ADDRESS BOOK] key to display the address book screen. (See page 1-4.) An auto-dial key is highlighted when touched. 3 Touch the [NEXT ADDRESS] key and then dial the fax number of the next destination or touch an auto-dial key. Repeat this step for SE NEXT ADDRESS each of the remaining destinations. X WITCH ADDRESS BOOK ADDRESS REVIEW 5 Check the destinations. When you have finished checking the ADDRESS REVIEW destinations, touch the 0666211221 SHARP GROUP CORPO. TPS [OK] key to return to the screen of step 4. If you wish to delete a DESELECT THE ADDRESS? 0666211221 destination, touch the displayed one-touch key. A message will appear to confirm NO YES the deletion. Touch [YES] and the destination will be deleted 3 from the destination list. To cancel instead of deleting, touch the [NO] key. 6 Continue from step 8 of "BASIC PROCEDURE FOR SENDING FAXES" (page 2-3). NOTE To cancel a broadcast transmission To cancel a broadcast transmission when selecting destinations, press the [CA] key. To cancel after all steps of the transmission have been completed, see "CANCELING A FAX TRANSMISSION" on page 2-9. NOTES G If you enter an incorrect number If you make a mistake while entering a number, press the [C] key and then re-enter the correct digit(s). If you have already completed entry of a fax number, you can delete the number using steps 4 and 5. G If you select an incorrect auto-dial key Simply touch the incorrect key one more time to cancel the selection. G The [NEXT ADDRESS] key only needs to be pressed when successively dialing fax numbers with the numeric keys Example: XXXX NEXT ADDRESS XXXX Dial Dial Cannot be omitted. XXXX NEXT ADDRESS One-touch NEXT ADDRESS One-touch Dial Can be omitted. Can be omitted. If desired, you can use the key operator program to set the machine so that the [NEXT ADDRESS] key must always be pressed (refer to page 8-4). 4 Touch the [ADDRESS REVIEW] key to display the list of destinations. CONDITION SETTINGS When the [ADDRESS REVIEW] key is touched, only the ADDRESS REVIEW entered and selected destinations are SUB ADDRESS displayed. Checking the results of a broadcast transmission and resending when an error occurs The results of a broadcast transmission can be viewed in the following screen, which is opened by touching the [BROADCAST: XXXX] key (where "XXXX" is the number of the job; see "NOTES" on page 2-3) in the finished job screen and then the [DETAIL] key. * Can only be used on the AR-M355N/AR-M455N. The AR-M355U/AR-M455U models do not have this function. DETAIL OF BROADCAST xxxx ADDRESS 002 HQ ADMIN. START TIME 10:01 11/01 STATUS NGXXXXX OK RETRY 1/ 1 010 SENDAI BRANCH 10:01 11/01 NGXXXXX FILE FAILED ALL DESTINATIONS (A) (B) (C) (A) [FILE] tab This only appears if the job was stored using the filing function. If the job was stored and transmission to a destination was not successful, the document image can be resent without scanning the document again. To call the destination and resend the image, switch to the [FAILED] or [ALL DESTINATIONS] tab. (B) [FAILED] tab This shows destinations to which transmission failed due to an error or other reason. The name of the destination, starting time, and transmission status appear. To call the destinations again, touch the [RETRY] key. (C) [ALL DESTINATIONS] tab This shows the name, starting time, and transmission status of all of the destinations of the broadcast transmission. All destinations can be called again by touching the [RETRY] key in this screen. 3-3