Sharp MX-M363N Installation Manual - Page 14
J. Function and operation check, K. Setup and adjustment data recording - toner cartridge
View all Sharp MX-M363N manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
J. Function and operation check Check that the following operations are normal. Check item list Key-in (operation panel) Display (operation panel) Paper feed Hand feed operation Main unit paper tray Desk unit paper feed tray Paper size detection Originals size Original table detection mode DSPF mode RSPF mode DSPF/RSPF S-S mode operation / two sided copy D-S mode S-D mode D-D mode Bookbinding operation Stapling operation Grouping operation Sorting operation Paper exit operation Equipped condition With the desk unit installed When the finisher is installed When the finisher is installed When the finisher is installed When the finisher is installed When the exit tray unit (MX-TRX2) is installed K. Setup and adjustment data recording Print the various setup data and the adjustment data (list) with SIM22-6 and keep the data. • In case of a memory trouble, if the data are not kept, all the adjustments must be made again. • If the data are kept, the setup values and the adjustment values can be entered without adjustments, shortening the servicing time. L. Necessary works before moving the machine 1) If the following options are installed, remove all of them from the machine. • Finisher • Large capacity tray 2) Remove the following consumable parts from the machine. • Paper • Toner cartridges • Development cartridge 3) Lock the following sections. • Scanner (Optical section) • Paper cassette lift plate NOTE: Since the hard disk drive is built in the machine, use care not to exert vibrations or shocks to the machine when in transit. M. Remote operation panel function Enable setting (1) General To use the remote operation panel function, the password for the remote operation panel function must be entered on the password input menu displayed on the VNC boot screen. Note that, therefore, the password must be set in advance to use the remote operation panel function. Let the user make the password, and use SIM26-78 to set it. (2) Remote operation panel function password setting procedures 1) Enter the SIM26-78 mode. ǂ7(ǂ6ǂ7 6,08/$7,21ǂǂ12 523(3$66:25'6(77,1* 35(6(17 1(:˖ &/26( 6(7 2) Enter the password with 10-key. (Within 5 - 8 digits) The entered password is displayed on the column of "NEW." To modify the entered password, use clear key to delete the password digit by digit. 3) Press [SET] key, and the password is set. N. USB PORT selection There are two USB ports; one on the front frame side and the other on the rear frame side. Only one of them can be used at a time. Do not connect the two USB ports simultaneously. When shipping, the port on the front frame side is valid and the port on the rear frame side is invalid. When using the USB port, be careful of the total current consumption not to exceed 500mA. The valid port can be switched by changing the setting of the MFP PWB DIP SW. Select the valid USB port according to the user's request. * The default setting for SW1/SW2 is OFF. MFP PWB DIP SW SW 1 SW 2 OFF OFF OFF ON USB I/F Port on the front Port on the rear frame side frame side Valid Invalid Invalid Valid Upper side: DIP-SW1 Lower side: DIP-SW2 When tilted toward you: OFF When tilted to the PWB side: ON NOTE: For the machine which is provided with a keyboard, either one of two USB ports can be used at a time. However, both DIP SW1's must be set to OFF. Note that, if DIP SW1 is set to ON, the machine is set to the CN update mode. NOTE: After completion of option installation, revise all the firmware to the latest version. MX-M503N MX-M283N/M363N/M363U/M453N/M453U/M503N/M503U/M282N/M362N/M452N/M502N 1 - 9