Sharp MX-M363N Installation Manual - Page 6

1 : '10/Jun/18 M[1X-]M50M3NX-M283N/M363N/M363U/ M453N/M453U/M503N/M503U/ 1 M282N/M362N/M452N/M502N 1. Installing (use) conditions Before installing the machine, check that the following installing (use) conditions are satisfied. If the installing (use) conditions are not satisfied, the machine may not display full performances, resulting in troubles. It may also cause safety problems. Therefore, be sure to arrange the installing (use) conditions before setting up the machine. No. Content 1 Bringing space 2 Installing space 3 Power source (Capacity, fluctuation, safety) 4 Floor strength 5 Direct rays of the sun, dust, temperature, humidity, gases, chemicals A. Bringing space For installation of a large size machine, be sure to check that the door size is wide enough before bringing in. B. Installing space The following space must be provided around the machine in order to assure machine performances and proper operations. If any option is installed, provide the additional space for installing it. Adequate space must be provide behind the machine for proper ventilation heat and dust. If not, the machine cannot exhibit functions against heat and dust, causing some troubles. 11-13/16" (30cm) 11-13/16" (30cm) 17-23/32" (45cm) S(3e)rvPiocweerMfraenquuaenlcy, waveform The frequency must be within the range of the specified frequency ±2%. If power waveform is deformed, a trouble may occur. (4) Safety Be sure to properly ground the machine. Grounding (earth connection) must be performed before inserting the power plug into the power outlet. When disconnecting the earth connection, be sure to disconnect the power plug from the power outlet in advance. (5) Power plug Check the shape of the power plug of the machine, and insert it into a power outlet of the acceptable shape. D. Floor strength and level This machine is considerably heavy and becomes heavier with an option installed. The floor must be strong enough for assuring safety. If the unit is not horizontally installed, the toner density control is not performed normally, degrading the copy quality. If not, color shift or image distortion may occur. E. Direct rays of the sun, dust, temperature, humidity, gasses, chemicals, vibration (1) Temperature and humidity This machine is designed to perform properly under the specified temperature and humidity. If the temperature and humidity exceeds the specified range, the machine may not operate properly and or cause equipment failure. Especially when the humidity is too high, paper absorbs humidity to cause a paper jam or dirty copy. Do not install the machine near a heater, a cooler, or a humidifier. C. Power source (Capacity, voltage, frequency, safety, plug) If the power specifications are not satisfied, the machine cannot exhibit full performances and may cause safety trouble. Strictly observe the following specifications. (1) Power capacity Check that the following power capacity is satisfied. If not, additionally provide a power source. Current capacity 1 100V: 15A or more 200V: 10A or more NOTE: Check the shape of the power plug of the machine, and insert it into a power outlet of the acceptable shape. (2) Power voltage Measure the voltage during copying to check that the voltage is in the range of the specified voltage ±10%. If the voltage is outside the specified range, use thicker lead wires to reduce impedance. (An electrical work is required.) Use of a step-up transformer is also available. In this case, the capacity must be great enough for the max. power consumption of the machine. Dew may be formed inside the machine to cause a trouble. Use enough care for ventilation. Humidity㧔RH㧕 85% 60% 20% • Working environment Temperature: 10 to 35°C Humidity: 20 to 85% RH Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m) MX-M503N MX-M283N/M363N/M363U/M453N/M453U/M503N/M503U/M282N/M362N/M452N/M502N 1 - 1