Sony HVR-Z5E Operation Guide - Page 87

Tc Run, Tc Make, Tc Link, Ub Time Rec, Ub-date/tc-time, Using The Menu, Reset, Regenerate

Get Sony HVR-Z5E PDF manuals and user guides View all Sony HVR-Z5E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

2 Select [PRESET] with the SEL/PUSH EXEC dial. 3 Select the first 2 digits with the SEL/PUSH EXEC dial. 4 Set other digits by repeating step 3. 5 Select [OK] with the SEL/PUSH EXEC dial. x RESET You can reset the user bit (00 00 00 00). Select [RESET] in step 1 of the [PRESET]. TC RUN You can select how the time code advances. B REC RUN Advances the time code only during recording. Select this setting to record the time code continuous from the last time code of the previous recording. FREE RUN Advances the time code regardless of operation of your camcorder. Select this setting to save the actual time in the time code. TC MAKE B REGENERATE Reads the last time code of the previous recording from the tape and records the new time code consecutively from the last time code during the backspace editing. The time code runs in [REC RUN] mode regardless of the setting of [TC RUN]. PRESET Records the newly set time code on the tape. TC LINK You can synchronize the time codes of multiple camcorders. This function is useful for editing movies recorded by multiple camcorders. 1 Insert a tape to the main camcorder from which you want to generate the time code. 2 Set the POWER switches of the main and sub camcorders to CAMERA. 3 Connect the sub camcorder to the main camcorder with an i.LINK cable. 4 Set the main and sub camcorder as follows: • Set [TC RUN] to [FREE RUN] (p. 87). • Set [TC MAKE] to [PRESET] (p. 87). Set the sub camcorders as follows: 5 Select [TC/UB SET] t [TC LINK] with the SEL/PUSH EXEC dial. The message [Synchronize TC with connected device?] appears. 6 Select [YES] to synchronize the time code of the sub camcorder with that of the main camcorder. Disconnect the i.LINK cable from your camcorders when synchronization is completed. You can record with the synchronized time codes using those camcorders. b Notes • If you want to execute [TC LINK] for more than two camcorders, repeat the steps for multiple sub camcorders with one main camcorder. • Some frame shifting may occur over time after time code synchronization. • Some frame shifting may occur if you turn the power off and back on. In such a case, set [TC LINK] again. UB TIME REC B OFF Does not save the actual time in the user bit code. ON Saves the actual time in the user bit code. UB-DATE/TC-TIME You can save the date and time set in your camcorder in the user bit and time code, respectively, when you do this function. Continued , 87 Using the Menu

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
87
Using the Menu
2
Select [PRESET] with the SEL/PUSH
EXEC dial.
3
Select the first 2 digits with the SEL/PUSH
EXEC dial.
4
Set other digits by repeating step
3
.
5
Select [OK] with the SEL/PUSH EXEC
dial.
x
RESET
You can reset the user bit (00 00 00 00).
Select [RESET] in step
1
of the
[PRESET].
You can select how the time code advances.
B
REC RUN
Advances the time code only during
recording.
Select this setting to record the time code
continuous from the last time code of the
previous recording.
FREE RUN
Advances the time code regardless of
operation of your camcorder.
Select this setting to save the actual time in
the time code.
B
REGENERATE
Reads the last time code of the previous
recording from the tape and records the
new time code consecutively from the last
time code during the backspace editing.
The time code runs in [REC RUN] mode
regardless of the setting of [TC RUN].
PRESET
Records the newly set time code on the
tape.
You can synchronize the time codes of
multiple camcorders.
This function is useful for editing movies
recorded by multiple camcorders.
1
Insert a tape to the main camcorder from
which you want to generate the time code.
2
Set the POWER switches of the main and
sub camcorders to CAMERA.
3
Connect the sub camcorder to the main
camcorder with an i.LINK cable.
4
Set the main and sub camcorder as follows:
•
Set [TC RUN] to [FREE RUN] (p. 87).
•
Set [TC MAKE] to [PRESET] (p. 87).
Set the sub camcorders as follows:
5
Select [TC/UB SET]
t
[TC LINK] with
the SEL/PUSH EXEC dial.
The message [Synchronize TC with
connected device?] appears.
6
Select [YES] to synchronize the time code
of the sub camcorder with that of the main
camcorder. Disconnect the i.LINK cable
from your camcorders when
synchronization is completed. You can
record with the synchronized time codes
using those camcorders.
b
Notes
•
If you want to execute [TC LINK] for more than
two camcorders, repeat the steps for multiple
sub camcorders with one main camcorder.
•
Some frame shifting may occur over time after
time code synchronization.
•
Some frame shifting may occur if you turn the
power off and back on. In such a case, set [TC
LINK] again.
B
OFF
Does not save the actual time in the user
bit code.
ON
Saves the actual time in the user bit code.
You can save the date and time set in your
camcorder in the user bit and time code,
respectively, when you do this function.
TC RUN
TC MAKE
TC LINK
UB TIME REC
UB-DATE/TC-TIME
Continued
,