Home » Sony Manuals » Stereo Systems » Sony STR DA5500ES » Manual Viewer

Sony STR DA5500ES Operating Instructions - Page 142

HDMI settings, For European model

UPC - 027242754324

Add to My Manuals
Save this manual to your list of manuals

Page 142 highlights

HDMI settings Makes the required settings for components connected to the HDMI jacks. Control for HDMI Lets you turn the function which controls components connected to the HDMI jack using an HDMI cable on or off. x OFF x ON Note When you set "Control for HDMI" to "ON," "Audio Out" may be changed automatically. For European model When "Control for HDMI" is turned on and off, the H.A.T.S. (High quality digital Audio Transmission System) function turns on and off in conjunction with the "Control for HDMI" function. When the H.A.T.S. function is on, the sound quality is enhanced because there is no jitter (timing gaps when reading signals) when transmitting digital audio signals. Notes • It takes some time to output the sound after a playback operation is performed on the connected component (e.g., pressing the PLAY button, pressing the STOP button, pressing the PAUSE button) due to limitations of the H.A.T.S. system. The time lag depends on the sound source. This feature may be ineffective depending on the component and the sound source, even if you set it to ON. • The components connected to the HDMI jack must support the H.A.T.S. feature. • When "Audio Out" is set to "TV+AMP," the H.A.T.S. function may not work depending on the component connected or the status of that component. In this case, select "AMP" for "Audio Out." • The H.A.T.S. function of this receiver works when a Sony SCD-XA5400ES is connected to the receiver. Stream information about the H.A.T.S. function available Audio signal input Sampling frequency Linear PCM 2ch 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz Linear PCM Multi 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz DSD 2.8224 MHz Pass Through Lets you output the HDMI signals to the TV even when the receiver is in standby mode. For details, see "Outputting the HDMI signals even when the receiver is in standby mode (Pass Through)" (page 116). x OFF x AUTO x ON Note When "Control for HDMI" is set to "OFF," you cannot set "Pass Through." Audio Out (Setting HDMI audio input) Lets you set the HDMI audio signals output from the playback component connected to the receiver via an HDMI connection. x TV+AMP The sound is output from the TV speaker and the speakers connected to the receiver. 142GB

Section	Page
Table of Contents	6
Description and location of parts	8
Getting Started	21
1: Installing speakers	21
2: Connecting the monitor	25
3a: Connecting the audio components	27
3b: Connecting the video components	32
3c: Connecting the IR Blaster	42
4: Connecting the antennas (aerials)	44
5: Connecting to the network	45
6: Preparing the receiver and the remote	47
7: Setting the speakers	48
8: Calibrating the appropriate speaker settings automatically (Auto Calibration)	50
9: Configuring the network settings of the receiver	57
10: Preparing a computer to use as a server	58
Guide to on-screen display operation	59
Playback	62
Enjoying sound/images from the component connected to the receiver	62
Enjoying sound/images from the components connected to the DIGITAL MEDIA PORT	64
Operating the TDM-iP50 using the GUI menu of the receiver	65
Tuning	68
Listening to FM/AM radio	68
Presetting FM/AM radio stations	71
Listening to satellite radio (USA/Canadian model only)	73
Connecting a satellite radio tuner	74
Preparing to listen to a satellite radio	74
Selecting a channel of the satellite radio	75
Presetting satellite radio channels	77
Restricting access to specific channels (Parental Lock) (SIRIUS only)	78
Enjoying Surround Sound	82
Playing back with 2-channel sound	82
Playing back with multi-channel surround	83
Enjoying a surround effect for music	86
Enjoying a surround effect for movies	88
Using Network Features	92
About the network functions of the receiver	92
What you can do with the home network function	93
Enjoying content stored on the server	96
Listening to Rhapsody	98
Listening to SHOUTcast	101
Features of the ES Utility application software	103
Using Multi-zone Features	105
What you can do with the Multi-zone function	105
Making a multi-zone connection	106
Setting the speakers in zone 2	108
Switching the zone setting of the remote	109
Operating the receiver from another zone (ZONE 2/ZONE 3 operations)	109
Listening to the same music in different zone (Party Mode)	110
Using Other Features	112
Using “BRAVIA” Sync features	112
Switching the monitors that output the HDMI video signals	116
Outputting the HDMI signals even when the receiver is in standby mode (Pass Through)	116
Switching between digital and analog audio	117
Enjoying the sound/ images from other inputs (Input Assign)	118
Using the sleep timer	121
Enjoying the surround effect at low volume levels	122
Recording using the receiver	123
Switching the command mode of the receiver and the remote	124
Using a bi-amplifier connection	126
Adjusting Settings	127
Using the setting menu	127
Auto Calibration	128
Speaker settings	130
Surround settings	134
EQ settings	136
Multi Zone settings	136
Audio settings	138
Video settings	140
HDMI settings	142
Network settings	144
Quick Click settings	145
System settings	146
Operating without connecting to a TV	147
Operating Each Component Using the On-screen Remote (Quick Click)	153
Operating components or lighting connected to the receiver using the on-screen remote (Quick Click)	153
Using Quick Click	154
Setting components that are operated by the on- screen remote	160
Performing several commands in sequence automatically with Quick Click (Macro Play)	165
Setting remote control codes that are not stored in Quick Click	167
Resetting the remote code for Quick Click	168
Operating Each Component Using the Multifunction Remote	170
Operating each component using the multifunction remote	170
Programming the remote	172
Performing several commands in sequence automatically (Macro Play)	175
Setting remote commander codes that are not stored in the remote	177
Clearing all the contents of the remote’s memory	179
Additional Information	180
Glossary	180
Precautions	184
Troubleshooting	185
Specifications	192

Match case Limit results 1 per page

142

HDMI settings

Makes the required settings for components

connected to the HDMI jacks.

Lets you turn the function which controls

components connected to the HDMI jack

using an HDMI cable on or off.

OFF

Note

When you set “Control for HDMI” to “ON,” “Audio

Out” may be changed automatically.

For European model

When “Control for HDMI” is turned on and

off, the H.A.T.S. (High quality digital Audio

Transmission System) function turns on and

off in conjunction with the “Control for

HDMI” function. When the H.A.T.S. function

is on, the sound quality is enhanced because

there is no jitter (timing gaps when reading

signals) when transmitting digital audio

signals.

Notes

• It takes some time to output the sound after a

playback operation is performed on the connected

component (e.g., pressing the PLAY button,

pressing the STOP button, pressing the PAUSE

button) due to limitations of the H.A.T.S. system.

The time lag depends on the sound source. This

feature may be ineffective depending on the

component and the sound source, even if you set it

to ON.

• The components connected to the HDMI jack must

support the H.A.T.S. feature.

• When “Audio Out” is set to “TV+AMP,” the

H.A.T.S. function may not work depending on the

component connected or the status of that

component. In this case, select “AMP” for “Audio

Out.”

• The H.A.T.S. function of this receiver works when

a Sony SCD-XA5400ES is connected to the

receiver.

Stream information about the

H.A.T.S. function available

Lets you output the HDMI signals to the TV

even when the receiver is in standby mode. For

details, see “Outputting the HDMI signals

even when the receiver is in standby mode

(Pass Through)” (page 116).

OFF

AUTO

Note

When “Control for HDMI” is set to “OFF,” you

cannot set “Pass Through.”

Lets you set the HDMI audio signals output

from the playback component connected to the

receiver via an HDMI connection.

TV+AMP

The sound is output from the TV speaker and

the speakers connected to the receiver.

Control for HDMI

Audio signal input

Sampling frequency

Linear PCM 2ch

44.1 kHz, 48 kHz,

88.2 kHz, 96 kHz,

176.4 kHz, 192 kHz

Linear PCM Multi

44.1 kHz, 48 kHz,

88.2 kHz, 96 kHz,

176.4 kHz, 192 kHz

DSD

2.8224 MHz

Pass Through

Audio Out (Setting HDMI audio

input)