Sony VPL-CX76 Operating Instructions - Page 43

Caution Messages, Message, Meaning and Remedy

Get Sony VPL-CX76 - Portable Wireless Networking LCD Business Projector PDF manuals and user guides
UPC - 027242666238
View all Sony VPL-CX76 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Message Frequency is out of range! Please check Input-A Signal Sel. Please replace the Lamp. Please clean the filter. Meaning and Remedy • This input signal cannot be projected as the frequency is out of the acceptable range of the projector. c Input a signal that is within the range of the frequency. • The resolution setting of the output signal of the computer is too high. c Set the output setting to XGA (see page 13). You have input an RGB signal from the computer when "Input-A Signal Sel." on the SET SETTING menu is set to "Component." c Set "Input-A Signal Sel." correctly (see page 29). • It is time to replace the lamp. c Replace the lamp. • When this message appears even after replacing the lamp, the task has not been completed. c Perform the operation of steps 8 and 9 on page 37. c To erase a message, press any key on the control panel of the projector or on the remote commander. It is time to clean the filter. c Clean the filter (see page 38). Caution Messages Use the list below to check the meaning of the messages displayed on the screen. Message Meaning and Remedy Not applicable! You have pressed the wrong key. c Press the appropriate key. The panel keys are locked! "Panel Key Lock" on the INSTALL SETTING menu is set to "On." c All the keys on the control panel of the projector are locked. Operate the projector with the keys on the Remote Commander (see page 30). Others Troubleshooting 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
43
Troubleshooting
Others
Caution Messages
Use the list below to check the meaning of the messages displayed on the screen.
Frequency is out of range!
• This input signal cannot be projected as the frequency is out of the
acceptable range of the projector.
c
Input a signal that is within the range of the frequency.
• The resolution setting of the output signal of the computer is too
high.
c
Set the output setting to XGA (see page 13).
Please check Input-A
Signal Sel.
You have input an RGB signal from the computer when “Input-A
Signal Sel.” on the SET SETTING menu is set to “Component.”
c
Set “Input-A Signal Sel.” correctly (see page 29).
Please replace the Lamp.
• It is time to replace the lamp.
c
Replace the lamp.
• When this message appears even after replacing the lamp, the task
has not been completed.
c
Perform the operation of steps
8
and
9
on page 37.
c
To erase a message, press any key on the control panel of the
projector or on the remote commander.
Please clean the filter.
It is time to clean the filter.
c
Clean the filter (see page 38).
Message
Meaning and Remedy
Not applicable!
You have pressed the wrong key.
c
Press the appropriate key.
The panel keys are locked!
“Panel Key Lock” on the INSTALL SETTING menu is set to “On.”
c
All the keys on the control panel of the projector are locked.
Operate the projector with the keys on the Remote Commander
(see page 30).
Message
Meaning and Remedy